1~60kVA Power Inverter for Solar Power System
1〜60kVA太阳能发电系统逆变器
| 型号。 | SNI-015 |
| 输出功率 | 1kVA至60kVA |
| 牌 | SNAT |
| 能量源 | 太阳能发电，太阳能发电 |
| 功能 | 自动旁路模式 |
| OEM / ODM | 接受 |
| 应用 | 电力 |
| 规范 | CE; ISO9001 |
| HS编码 | 8504403090 |
| 相 | 单 |
| 证明 | ce，iso9001 |
| 类型 | 直流/交流逆变器 |
| 波弦的性质 | 正弦波逆变器 |
| 频率 | 电源频率 |
| 特殊的设计 | 接受 |
| 商标 | SNAT |
| 起源 | 广东佛山 |
生产介绍：
本系列变频双变电源系统.当电网出现停电，电压不稳定，电压干扰，浪涌，峰值和电源噪声等不良现象，可以保证负载工作正常。
应用：
广泛应用于电力，通信，广播电视，银行，税务和IT行业等。为设备负载提供优质的稳定电源。
工作准则：
也不操作不良
电池通过隔离二极管转换为逆变电源， 然后通过变频器变换成稳定的交流（ac）， 通过静态开关切换到EMI输出滤波器进行滤波， 最后在输出端也可以获得纯稳定的电源给负载。 从变频器故障到主电源，整个过程输出不间断时间。 同时，电源通过另一个分支供电给充电器后转换成电池充电。展示如下：
2.自动旁路操作
在以下情况下，变频器将自动切换到旁路状态电源：
1）前面板的“ON / OFF”按钮开关不需要触发启动，或者在触发后不能超过20秒测试时间延迟。
2) 待机状态
3) 变频器出来放置过载或电池电压低
4) INV电路错误 内建的 故障
当有上述情况时，输入电源通过滤波器后，不再通过变频器切换，而是直接到静态开关，切换到滤波器后再过滤输出。在旁路状态下，电源也可以为电池充电。
技术参数
(1)单一单出技术参数
| 1KL~20kl(单入 单出模型) 技术参数表 | |||||||
| 模型 | 1KL | 2KL | 3KL | 6kl | 10kl | 15kl | 20kl |
| 额定电容TY（KW） | 1kav | 2kav | 3kav | 6kav | 10kav | 15kav | 20kav |
| 输入电压 | 单相 两线+地线， 220V±±plusmn;±25% | ||||||
| 电池电压 | 48VDC | 96 / 192VDC | 192 / 240VDC | ||||
| 噪声 | ≤≤le;≤52分贝（距离1m) | ≤≤le;≤60分贝（距离1m) | |||||
| 尺寸 （宽*深*高mm) | 256××times;×618××times;×626 | 370××times;×690××times;×763 | |||||
| 重量（kg） | 30 | 40 | 45 | 60 | 105 | 130 | 160 |
(2) 三进一唱e出技术参数
| rld6kl~60KL(三进 单出模型) 技术参数表 | ||||||||
| 模型 | 10kl | 15kL | 20kl | 30kl | 40kl | 50kl | 60KL | |
| 额定电容TY（KW） | 10kav | 15kav | 20kav | 30kav | 40kav | 50kav | 60kav | |
| 输入电压 | 三相 四线+地线， 3800V±±plusmn;±25% | |||||||
| 电池电压 | 384vdc | |||||||
| 噪声 | ≤≤le;≤60分贝（距离1m) | ≤≤le;≤65分贝（距离1m) | ||||||
| 尺寸 （宽*深*高mm) | 370××times;×690××times;×763 | 650×700×160000×1600s;160000×1600 | ||||||
| 重量（kg） | 165 | 190 | 210 | 400 | 450 | 530 | 620 | |
(3) 单成单出，三成单出一般技术参数
| 单成单出，三成单出一般技术参数 | ||
| 输入 | 频率 | 50Hz / 60Hz的±10％usmn; 10％usmn;10% |
| 功率因数 | ≥≥ge;≥80% | |
| 产量 | 电压 | 220V±1％lusmn; 1％lusmn;1% |
| 电压调节 | 调控±1％，usmn; 1％，usmn;1%,动态±2％，usmn; 2％，usmn;2%,（0-100％负载变化 < 20 ms) ms) | |
| 频率稳定性 | 50Hz / 60Hz的±0.5％SMN; 0.5％smn;0.5%（电池供电） | |
| 频率到利率 | 小于1 赫兹/秒。 | |
| 谐波失真 | 线性负载 小于3％（负载），整流总谐波小于5％ | |
| 过载能力 | 130% | |
| 波形 | 波形 | |
| 效率 | 输入AC到 输出AC | 超过95% |
| 转移时间 | 电源和电池之间的转换 | 0秒 |
| 变频器和旁路之间的转换 | 小于4 毫秒 | |
| 电池 | 类型 | 铅酸se免费维护 |
| 充电时间 | 完全放电8小时后充电至90％ | |
| 报警歌 | 超载load | 输出过载，每1秒鸣叫一次 |
| 输出严重过载保护，连续鸣叫 | ||
| 电池放电 | 电源电源故障，每4秒鸣叫一次 | |
| 电池低电压蜂鸣每1秒一次 | ||
| 电池放电停止，连续啁啾 | ||
| 故障异常 | 连续啁啾 | |
| 保护性能 | 电池 | 电池低电量自动跳到旁路，电池饱和后自动恢复 |
| 超载 | 超载（120〜150％）30秒后自动跳转到旁路，自动恢复 | |
| 过温 | 逆变器internal温度> 85; 85 ºCordm;Çordm;C，自动跳转到BYPASS | |
| 输出短路 电路 | 电流限制和自动关机，保险丝和无保险丝开关保护 | |
| 逆变器ano马利 | 自动跳到BYPASS和电源 | |
| 液晶显示器 | 液晶显示器 信息 | 显示input和输出电压，频率，电池电压，输出负载 |
| 环境 | 温度 | -10〜50℃（RDM; C（rdm;C( |
| 相对湿度 | 20% 至 93% （非冷凝） | |
| 高度 | 高度 1000m以下 | |
常问问题：
q1：moq
答：我公司最低起订量为1个单位
Q2：你是制造商还是贸易公司？
A：自2004年以来我们是专业制造商
Q3：我需要这个产品，想要一个家庭/工业/商业用的系统，你能帮我吗？
答：是的，我们有专业的技术团队10年的经验，可以根据客户的特殊要求设计太阳能发电系统。
问4：您的交货时间多久？
A：15天内
Q5：您的售后服务如何？
A: 我们质量保证2年;任何部件将在保修期内免费发货。
公司简介
作为电力和新能源解决方案的领先供应商，专注于新能源的电能公司，SNAT具有强大的实力，从事电能和新能源。其主要五大产品包括逆变器，U PS，太阳能控制器。太阳能逆变器和电池广泛应用于电力市场，基础设施市场和工业市场自成立以来。 SNAT一直是世界新能源领域的先驱
| Model NO. | SNI-015 |
| Output Power | 1kVA to 60kVA |
| Brand | Snat |
| Power Source | Solar Power, Solar Power |
| Function | Automatic Bypass Mode |
| OEM/ODM | Accept |
| Application | Electric Power |
| Specification | CE; ISO9001 |
| HS Code | 8504403090 |
| Phase | Single |
| Certification | CE, ISO9001 |
| Type | DC/AC Inverters |
| Nature of Wave String | Sine Wave Inverter |
| Frequency | Power Frequency |
| Special Design | Accept |
| Trademark | SNAT |
| Origin | Foshan Guangdong |
Production Introduction:
This series inverter for double transformation power supply system.When the power grid appear outage, voltage instability, voltage interference, surge, peak and mains noise and other bad phenomenon, can guarantee the load working normally.
Application:
Widely used in electric power, communication, radio and television, banking, taxation and IT industry etc. To provide quality stable power for equipment load.
Working principle:
1. normal operation
Battery through the isolation diode to inverter power supply, and then by inverter transformation into stable alternating current (ac), Through static switch switch to EMI output filter for filtering, Finally on the output side also get a pure stable power supply to the load. From the inverter fault to the mains supply the entire process output no intermittent time. At the same time, the mains through another branch supply to charger after transformation to the battery charging. Showen as below:
2. Automatic bypass operation
When in the following situations inverter will automatically switch to bypass state power supply:
1)The front panel 'ON/OFF' button switch without press the trigger boot, or after trigger not go by 20 seconds testing time delay.time delay.
2) Standby state
3) Inverter output overload or battery low voltage
4) inverter circuit built-in malfunction
When there is above circumstance, after the input mains through the filter, is no longer through the inverter switching, but directly to the static switch, after switch to the filter and then filter output. In the bypass state, mains also can charge for the battery.
Technical parameters
(1)Single into single out technical parameters
| 1KL~20KL(Single into single out model) technology parameter list | |||||||
| Model | 1KL | 2kL | 3KL | 6KL | 10KL | 15KL | 20KL |
| Rated capacity(KW) | 1KAV | 2KAV | 3KAV | 6KAV | 10KAV | 15KAV | 20KAV |
| Input voltage | Single phase two line + ground line, 220V±±plusmn;±25% | ||||||
| Battery voltage | 48VDC | 96/192VDC | 192/240VDC | ||||
| noise | ≤≤le;≤52dB(Distance 1m) | ≤≤le;≤60dB(Distance 1m) | |||||
| size (W*D*Hmm) | 256××times;×618××times;×626 | 370××times;×690××times;×763 | |||||
| Weight(kg) | 30 | 40 | 45 | 60 | 105 | 130 | 160 |
(2) three into single out technical parameters
| RLD6KL~60KL(three into single out model) technology parameter list | ||||||||
| Model | 10KL | 15kL | 20KL | 30KL | 40KL | 50KL | 60KL | |
| Rated capacity(KW) | 10KAV | 15KAV | 20KAV | 30KAV | 40KAV | 50KAV | 60KAV | |
| Input voltage | three phase four line + ground line, 3800V±±plusmn;±25% | |||||||
| Battery voltage | 384VDC | |||||||
| noise | ≤≤le;≤60dB(Distance 1m) | ≤≤le;≤65dB(Distance 1m) | ||||||
| size (W*D*Hmm) | 370××times;×690××times;×763 | 650×700×160000×1600s;160000×1600 | ||||||
| Weight(kg) | 165 | 190 | 210 | 400 | 450 | 530 | 620 | |
(3) Single into single out and three into single out general technical parameter
| Single into single out and three into single out general technical parameter | ||
| Input | frequency | 50Hz/60Hz±10%usmn;10%usmn;10% |
| Power factor | ≥≥ge;≥80% | |
| Output | Voltage | 220V±1%lusmn;1%lusmn;1% |
| Voltage adjustment | Regulated±1%,usmn;1%,usmn;1%,dynamic±2%,usmn;2%,usmn;2%,(0-100% load change < 20 ms) ms) | |
| Frequency stability | 50Hz/60Hz±0.5%smn;0.5%smn;0.5%(battery powered) | |
| Frequency torsional rate | Less than 1 hz/sec. | |
| Harmonic distortion | Linear load is less than 3% (load), rectifier total harmonic is less than 5% | |
| Overload capacity | 130% | |
| waveform | Wave form | |
| efficiency | Input AC to output AC | More than 95% |
| transfer time | Transfer between mains and battery | 0 seconds |
| Transfer between inverter and bypass | Less than 4 millisecond | |
| battery | type | Lead-acid seal free maintenance |
| Charging time | After completely discharge 8 hours and charged to 90% | |
| Alarm song | Overload load | Output overload, tweet once every 1 second |
| Output severe overload protection, continuous tweets | ||
| Battery discharge | Mains power supply failure, tweet once every 4 seconds | |
| Battery low voltage beep once every 1 second | ||
| The battery discharge will stop, continuous chirping | ||
| Fault anomaly | continuous chirping | |
| Protection performance | battery | Battery low energy automatic to jump to BYPASS,after the battery saturation automatically recovery |
| overload | Overload (120 ~ 150%) 30 seconds later automatic to jump to BYPASS, automatic recovery | |
| Over temperature | Inverter internal temperature ﹥ 85; 85 ºCordm;Cordm;C, automatic to jump to BYPASS | |
| Output short circuit | The current limit and automatic shutdown, fuse and no fuse switch protection | |
| Inverter anomaly | Automatic to jump to BYPASS and the mains supply | |
| LCD display | LCD display information | Display input and output voltage, frequency, battery voltage, output load |
| environment | temperature | -10~50ºC(rdm;C(rdm;C( |
| Relative humidity | 20% to 93% (non-condensing) | |
| altitude | Altitude 1000m or less | |
FAQ:
Q1: MOQ
A: MOQ from our company is required 1 unit
Q2: Are you manufacturer or trading company?
A: We are professional manufacturer since 2004
Q3:I need this product and wanna a system for family/industrial/commerical using, can you help me?
A: Yes, we have a professional technology team average 10 years' experience, they can design solar power system in accordance with customers' special requirements.
Q4: How long is your delivery time
A: Within 15 days
Q5:How about your after-sales service?
A: Our quality warranty for 2 years; any parts will be shipped for free during warranty period.
Company profile
As a worid's leading supplier for solutions for electric energy and new energy and an electric energy company specialized in new energy, SNAT has powerful strength and is engaged in both electric energy and new energy. Its main five kinds of products including inverters, U PS, solar controllers. solar inverters and batteries are widely used in the electric power market, the infrastructure market and the industrial market Since its establishment. SNAT has been being a pioneer in the world's new energy field
