Must off Grid System Pure Sine Wave 48V 4000W Inverter

Must off Grid System Pure Sine Wave 48V 4000W Inverter

必须关闭网格系统纯正弦波48V 4000W逆变器

1+
173 USD
10+
163 USD
31+
149 USD

加入意向
型号。 ep3000 1kw-6kw
正弦波 纯正弦波
最大电流10A： 充电器里面
显示 LED / LCD
模型 1-6kw
项目 直流到交流电源逆变器
运输包装 纸箱或木制
起源 中国深圳
颜色 黑与白
材料 Metel案例
重量 >22公斤;22公斤
峰值功率 3次正常
输入电压 110V / 220V
商标 必须或OEM品牌可用
规范 ce，iso9001＆14000; 1400014000
HS编码 8504402000
必须关闭电网系统纯正弦波48v 4000w逆变器

电力变频器1KW-6KW太阳能逆变器
耐用的建筑，在极端环境条件下长寿命
低空闲电流（小于1瓦）在没有负载的情况下节省能量
启动重载荷的软起动能力
内置起动控制电路，用于二线和三线发电机起动系统
简单的控制与一个卡扣式盖子，保护设置不被意外更改
更好的热性能可使全输出功率达到50°C（122°F），而无需降额评级de-rating
高浪涌能力开始更困难的负载，并可靠地处理过载条件
耐磨粉末涂层，耐腐蚀钢底盘
新数字显示器在倒相时显示千瓦（kW），充电时显示AMPS（A），加上强大的ON / OFF开关和状态指示灯
70-AMP自动三级电池充电器（散装，吸收和浮动）和电池均衡与远程温度传感器，以提高性能
新的功率因数校正（PFC）充电，结合更复杂的多级电池充电算法，可以减少耗电量和发电机运行时间
模型
（ep3000）		 HV型号
1012E 1024E 2012E 2024E 3024E 4048E 5048E 6048E
线模式规格：
输入电压波形 正弦（效用或发电机）
标称输入电压 230Vac（120VAC可选）
低线断开 184Vac±4％lusmn; 4％lusmn;4%
低线重新连接 194Vac±4％lusmn; 4％lusmn;4%
高线断开 265VAC±4％lusmn; 4％lusmn;4%
高线重新连接 255Vac±4％lusmn; 4％lusmn;4%
最大交流输入电压 270Vrms
标称输入频率 50Hz / 60Hz（自动检测）
低线频率重新连接 60Hz时为58 + 0.3Hz; 50Hz为48 + 0.3Hz;
低线频率断开 60Hz为57 + 0.3Hz，50Hz为47 + 0.3Hz;
高线频率重新连接 60Hz为64 + 0.3Hz，50Hz为54 + 0.3Hz;
高线频率断开
60Hz为65 + 0.3Hz; 50Hz为55 + 0.3Hz;
输出电压波形 与输入波形相同
过载保护（SMPSload） 断路器
输出短路保护 断路器
效率（线路模式） >95%
转换开关额定值 30A
转移时间（Ac到Dc） 10ms（典型值）
转移时间（Dc到Ac） 10ms（典型值）
通过没有电池 是
最大旁路过载电流 30A
反转模式规格：
输出电压波形 正弦波
额定输出功率（VA） 1000 2000 3000 4000 5000 6000
额定输出功率（W） 1000 2000 3000 4000 5000 6000
功率因数 0~1.0
标称输出电压（V） 230V交流
额定输出频率（Hz） 50Hz±0.3Hzn; 0.3Hzn; 0.3Hz
自动跟踪主频率（Hz） 是（主要第一次连接）50Hz @ 48-54Hz; 60Hz @ 58-64Hz
输出电压调节 ±10％rms; 10％rms;10% rms
名义效率 >80%

过载保护
（SMPS负载）		 （110％150％±10％：20秒后的故障（停机输出）; 20秒;ter 20s;
浪涌等级（10s） 3000VA 6000VA 9000va 12000va 15000 va 18000va
能启动电动机 1马力 1马力 2马力 3马力
输出短路保护 电流限制（10s后故障）
旁路断路器尺寸 30A 30A 30A 35A 50A
标称直流输入电压 12V 24V 12V 24V 24V 48V 48V
最小直流启动电压 10V / 20V / 40V
低电量报警 10.5Vdc±0.3Vdc为12V电池; 21.0Vdc±0.6Vdc为24V电池; 42.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
低直流输入关断 10.0Vdc±0.3Vdc为12V电池; 20.0vdc±0.6Vdc为24V电池; 40.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
高直流输入报警和故障缺陷Fault 16Vdc±0.3Vdc，12V电池; 32Vdc±0.6Vdc，24V电池; 64Vdc±0.6Vdc，48V电池0.6Vdc，48V电池0.6Vdc for 48V battery
高直流输入恢复 15.5Vdc±12V电池为±0.3Vdc; 24V电池为31.0Vdc±0.6Vdc; 62.0Vdc±0.6Vdc，48V电池，0.6Vdc，48V电池0.6Vdc for 48V battery
省电器 负载≤25W（远程控制的“P / S自动”设置启用）表情控制）rol)
充电模式规格：
标称输入电压 230V交流
输入电压范围 196〜243Vac
标称输出电压 根据电池类型
标称充电电流 35A 35A 65A 35A 45A 35A 40A 50A
充电电流调节 ±5Adcmn; 5Adcmn; 5Adc
电池初始电压 0 -15.7 Vdc（可以使用0V电池）
充电器短路保护 断路器
过充电保护 蝙蝠。 V≥15.7Vdc/ 31.4Vdc，60s后60s，每1s发生嘟嘟声0.5sfter 60s
一般规格
安全认证 CE
安全认证 FCC
工作温度范围 0°C至40°C 40°Ceg;C 40°C
储存温度 15°C低于零至60°C 60°Ceg;C 60°C
工作湿度 5％至95％
声音噪音 最大60dB
冷却 强制空气，变速风扇
尺寸 1012E / 1024E / 2012E / 2024e / 2048e / 3012e / 3024e / 3048e：580x315x300mm
4048e / 5048e // 6048e：755x319x288mm
模型
（ep3000）		 HV型号
1012E 1024E 2012E 2024E 3024E 4048E 5048E 6048E
线路模式规格：
输入电压波形 正弦（效用或发电机）
标称输入电压 230Vac（120VAC可选）
低线断开 184Vac±4％lusmn; 4％lusmn;4%
低线重新连接 194Vac±4％lusmn; 4％lusmn;4%
高线断开 265VAC±4％lusmn; 4％lusmn;4%
高线重新连接 255Vac±4％lusmn; 4％lusmn;4%
最大交流输入电压 270Vrms
标称输入频率 50Hz / 60Hz（自动检测）
低线频率重新连接 60Hz时为58 + 0.3Hz; 50Hz为48 + 0.3Hz;
低线频率断开 60Hz为57 + 0.3Hz，50Hz为47 + 0.3Hz;
高线频率重新连接 60Hz时为64 + 0.3Hz; 50Hz为54 + 0.3Hz;
高线频率断开
60Hz为65 + 0.3Hz; 50Hz为55 + 0.3Hz;
输出电压波形 与输入波形相同
过载保护（SMPSload） 断路器
输出短路保护 断路器
效率（线路模式） >95%
转换开关额定值 30A
转移时间（Ac到Dc） 10ms（典型值）
转移时间（Dc到Ac） 10ms（典型值）
通过没有电池 是
最大旁路过载电流 30A
反转模式规格：
输出电压波形 正弦波
额定输出功率（VA） 1000 2000 3000 4000 5000 6000
额定输出功率（W） 1000 2000 3000 4000 5000 6000
功率因数 0~1.0
标称输出电压（V） 230V交流
额定输出频率（Hz） 50Hz±0.3Hzn; 0.3Hzn; 0.3Hz
自动跟踪主频率（Hz） 是（主要第一次连接）50Hz @ 48-54Hz; 60Hz @ 58-64Hz
输出电压调节 ±10％rms; 10％rms;10% rms
名义效率 >80%

过载保护
（SMPS负载）		 （110％150％±10％：20秒后的故障（停机输出）; 20秒;ter 20s;
浪涌等级（10s） 3000VA 6000VA 9000va 12000va 15000 va 18000va
能启动电动机 1马力 1马力 2马力 3马力
输出短路保护 电流限制（10s后故障）
旁路断路器尺寸 30A 30A 30A 35A 50A
标称直流输入电压 12V 24V 12V 24V 24V 48V 48V
最小直流启动电压 10V / 20V / 40V
低电量报警 10.5Vdc±0.3Vdc为12V电池; 21.0Vdc±0.6Vdc为24V电池; 42.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
低直流输入关断 10.0Vdc±0.3Vdc为12V电池; 20.0vdc±0.6Vdc为24V电池; 40.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
高直流输入报警和故障缺陷Fault 16Vdc±0.3Vdc，12V电池; 32Vdc±0.6Vdc，24V电池; 64Vdc±0.6Vdc，48V电池0.6Vdc，48V电池0.6Vdc for 48V battery
高直流输入恢复 15.5Vdc±12V电池为±0.3Vdc; 24V电池为31.0Vdc±0.6Vdc; 62.0Vdc±0.6Vdc，48V电池，0.6Vdc，48V电池0.6Vdc for 48V battery
省电器 负载≤25W（远程控制的“P / S自动”设置启用）表情控制）rol)
充电模式规格：
标称输入电压 230V交流
输入电压范围 196〜243Vac
标称输出电压 根据电池类型
标称充电电流 35A 35A 65A 35A 45A 35A 40A 50A
充电电流调节 ±5Adcmn; 5Adcmn; 5Adc
电池初始电压 0 -15.7 Vdc（可以使用0V电池）
充电器短路保护 断路器
过充电保护 蝙蝠。 V≥15.7Vdc/ 31.4Vdc，60s后60s，每1s发生嘟嘟声0.5sfter 60s
一般规格
安全认证 CE
安全认证 FCC
工作温度范围 0°C至40°C 40°Ceg;C 40°C
储存温度 15°C低于零至60°C 60°Ceg;C 60°C
工作湿度 5％至95％
声音噪音 最大60dB
冷却 强制空气，变速风扇
尺寸 1012E / 1024E / 2012E / 2024e / 2048e / 3012e / 3024e / 3048e：580x315x300mm
4048e / 5048e // 6048e：755x319x288mm
模型
（ep3000）		 HV型号
1012E 1024E 2012E 2024E 3024E 4048E 5048E 6048E
线路模式规格：
输入电压波形 正弦（效用或发电机）
标称输入电压 230Vac（120VAC可选）
低线断开 184Vac±4％lusmn; 4％lusmn;4%
低线重新连接 194Vac±4％lusmn; 4％lusmn;4%
高线断开 265VAC±4％lusmn; 4％lusmn;4%
高线重新连接 255Vac±4％lusmn; 4％lusmn;4%
最大交流输入电压 270Vrms
标称输入频率 50Hz / 60Hz（自动检测）
低线频率重新连接 60Hz时为58 + 0.3Hz; 50Hz为48 + 0.3Hz;
低线频率断开 60Hz为57 + 0.3Hz，50Hz为47 + 0.3Hz;
高线频率重新连接 60Hz时为64 + 0.3Hz; 50Hz为54 + 0.3Hz;
高线频率断开
60Hz为65 + 0.3Hz; 50Hz为55 + 0.3Hz;
输出电压波形 与输入波形相同
过载保护（SMPSload） 断路器
输出短路保护 断路器
效率（线路模式） >95%
转换开关额定值 30A
转移时间（Ac到Dc） 10ms（典型值）
转移时间（Dc到Ac） 10ms（典型值）
通过没有电池 是
最大旁路过载电流 30A
反转模式规格：
输出电压波形 正弦波
额定输出功率（VA） 1000 2000 3000 4000 5000 6000
额定输出功率（W） 1000 2000 3000 4000 5000 6000
功率因数 0~1.0
标称输出电压（V） 230V交流
额定输出频率（Hz） 50Hz±0.3Hzn; 0.3Hzn; 0.3Hz
自动跟踪主频率（Hz） 是（主要第一次连接）50Hz @ 48-54Hz; 60Hz @ 58-64Hz
输出电压调节 ±10％rms; 10％rms;10% rms
名义效率 >80%

过载保护
（SMPS负载）		 （110％150％±10％：20秒后的故障（停机输出）; 20秒;ter 20s;
浪涌等级（10s） 3000VA 6000VA 9000va 12000va 15000 va 18000va
能启动电动机 1马力 1马力 2马力 3马力
输出短路保护 电流限制（10s后故障）
旁路断路器尺寸 30A 30A 30A 35A 50A
标称直流输入电压 12V 24V 12V 24V 24V 48V 48V
最小直流启动电压 10V / 20V / 40V
低电量报警 10.5Vdc±0.3Vdc为12V电池; 21.0Vdc±0.6Vdc为24V电池; 42.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
低直流输入关断 10.0Vdc±0.3Vdc为12V电池; 20.0vdc±0.6Vdc为24V电池; 40.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
高直流输入报警和故障缺陷Fault 16Vdc±0.3Vdc，12V电池; 32Vdc±0.6Vdc，24V电池; 64Vdc±0.6Vdc，48V电池0.6Vdc，48V电池0.6Vdc for 48V battery
高直流输入恢复 15.5Vdc±12V电池为±0.3Vdc; 24V电池为31.0Vdc±0.6Vdc; 62.0Vdc±0.6Vdc，48V电池，0.6Vdc，48V电池0.6Vdc for 48V battery
省电器 负载≤25W（远程控制的“P / S自动”设置启用）表情控制）rol)
充电模式规格：
标称输入电压 230V交流
输入电压范围 196〜243Vac
标称输出电压 根据电池类型
标称充电电流 35A 35A 65A 35A 45A 35A 40A 50A
充电电流调节 ±5Adcmn; 5Adcmn; 5Adc
电池初始电压 0 -15.7 Vdc（可以使用0V电池）
充电器短路保护 断路器
过充电保护 蝙蝠。 V≥15.7Vdc / 31.4Vdc，60s后60s，每1s发生嘟嘟声0.5sfter 60s
一般规格
安全认证 CE
安全认证 FCC
工作温度范围 0°C至40°C 40°Ceg;C 40°C
储存温度 15°C低于零至60°C 60°Ceg;C 60°C
工作湿度 5％至95％
声音噪音 最大60dB
冷却 强制空气，变速风扇
尺寸
1012E / 1024E / 2012E / 2024e / 2048e / 3012e / 3024e / 3048e：580x315x300mm
4048e / 5048e // 6048e：755x319x288mm

关于变频器安装：

关于我们：


请联系唐娜：
电话：+86 755 2910 1183
Model NO. EP3000 1KW-6KW
Sine Wave Pure Sine Wave
Max Current 10A: with Charger Inside
Display LED/LCD
Model 1-6kw
Item DC to AC Power Inverter
Transport Package Carton or Wooden
Origin Shenzhen, China
Color Black and White
Material Metel Case
Weight ﹥22kg;22kg
Peak Power 3 Times as Normal
Input Voltage 110V/220V
Trademark MUST or OEM brand is available
Specification CE, ISO9001&14000;1400014000
HS Code 8504402000
MUST off grid system Pure Sine Wave 48v 4000w inverter

Power inverter 1KW-6KW solar power Inverter
Durable construction for long life under extreme environmental conditions
Low idle current (less than 1 watt) conserves energy when no loads are present
Soft start capability for starting heavy loads
Built-in starting control circuits for two- and three-wire generator starting systems
Simplified controls with a snap-on cover that protects settings from being accidentally changed
Better thermal performance allows full output power to 50° C (122° F) without de-ratingde-ratingde-rating
High surge capacity starts more difficult loads and handles overload conditions reliably
Durable powder coated, corrosion resistant steel chassis
New digital display shows kilowatts (kW) when inverting and AMPS (A) when charging, plus incorporates a robust ON/OFF switch and status indicators
70-AMP automatic three-stage battery charger (bulk, absorption, and float) and battery equalization with remote temperature sensor for increased performance
New power factor corrected (PFC) charging, combined with a more sophisticated multi-stage battery charging algorithm, reduces electricity draw and generator run-time
MODEL
(EP3000)		 HV Model
1012E 1024E 2012E 2024E 3024E 4048E 5048E 6048E
Line Mode Specifications:
Input Voltage Waveform Sinusoidal (utility or generator)
Nominal Input Voltage 230Vac(120VAC selectable)
Low Line Disconnect 184Vac±4%lusmn;4%lusmn;4%
Low Line Re-connect 194Vac ±4%lusmn;4%lusmn;4%
High Line Disconnect 265Vac±4%lusmn;4%lusmn;4%
High Line Re-connect 255Vac±4%lusmn;4%lusmn;4%
Max AC Input Voltage 270Vrms
Nominal Input Frequency 50Hz/ 60Hz (Auto detection)
Low Line Frequency Re-connect 58+0.3Hz for 60Hz;48+0.3Hz for 50Hz;
Low Line Frequency Disconnect 57+0.3Hz for 60Hz;47+0.3Hz for 50Hz;
High Line Frequency Re-connect 64+0.3Hz for 60Hz;54+0.3Hz for 50Hz;
High Line Frequency Disconnect
65+0.3Hz for 60Hz;55+0.3Hz for 50Hz;
Output Voltage Waveform As same as Input Waveform
Over-Load Protection(SMPSload) Circuit breaker
Output Short Circuit Protection Circuit breaker
Efficiency (Line Mode) >95%
Transfer Switch Rating 30A
Transfer Time (Ac to Dc) 10ms (typical)
Transfer Time (Dc to Ac) 10ms (typical)
Pass through without Battery Yes
Max Bypass Overload Current 30A
Invert Mode Specifications:
Output Voltage Waveform Sine wave
Rated Output Power (VA) 1000 2000 3000 4000 5000 6000
Rated Output Power (W) 1000 2000 3000 4000 5000 6000
Power Factor 0~1.0
Nominal Output Voltage (V) 230Vac
Nominal Output Frequency (Hz) 50Hz ± 0.3Hzn; 0.3Hzn; 0.3Hz
Auto tracking Main Frequency(Hz) Yes (Following Main first connection)50Hz @48-54Hz ;60Hz @58-64Hz
Output Voltage Regulation ±10% rms;10% rms;10% rms
Nominal Efficiency >80%

Over-Load Protection
(SMPS load)		 (110% 150% ±10%: Fault (shutdown output) after 20s;ter 20s;ter 20s;
Surge rating (10s) 3000VA 6000VA 9000VA 12000VA 15000 VA 18000VA
Capable of starting electric motor 1 HP 1 HP 2 HP 3 HP
Output Short Circuit Protection Current limit (Fault after 10s)
Bypass Breaker Size 30A 30A 30A 35A 50A
Nominal DC Input Voltage 12V 24V 12V 24V 24V 48V 48V
Min DC start voltage 10V/20V/40V
Low Battery Alarm 10.5Vdc ± 0.3Vdc for 12V battery;21.0Vdc ± 0.6Vdc for 24V battery;42.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Low DC input Shut-down 10.0Vdc ± 0.3Vdc for 12V battery;20.0vdc± 0.6Vdc for 24V battery;40.0Vdc± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Alarm & FaultFaultFault 16Vdc ± 0.3Vdc for 12V battery;32Vdc ± 0.6Vdc for 24V battery; 64Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Recovery 15.5Vdc ± 0.3Vdc for 12V battery;31.0Vdc ± 0.6Vdc for 24V battery; 62.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Power saver Load ≤25W (Enabled on 'P/S auto' setting of Remote control)emote control)rol)
Charge Mode Specifications:
Nominal Input Voltage 230Vac
Input Voltage Range 196~243Vac
Nominal Output Voltage According to the battery type
Nominal Charge Current 35A 35A 65A 35A 45A 35A 40A 50A
Charge Current Regulation ± 5Adcmn; 5Adcmn; 5Adc
Battery initial voltage 0 -15.7 Vdc (can operate with 0V battery)
Charger Short Circuit Protection Circuit breaker
Over Charge Protection Bat. V ≥15.7Vdc/31.4Vdc,beeps 0.5s every 1s & fault after 60sfter 60sfter 60s
General Specifications
Safety Certification CE
Safety Certification FCC
Operating Temperature Range 0°C to 40°C 40°Ceg;C 40°C
Storage temperature 15°C below zero to 60°C 60°Ceg;C 60°C
Operation humidity 5% to 95%
Audible Noise 60dB max
Cooling Forced air, variable speed fan
Size 1012E/1024E/2012E/2024E/2048E/3012E/3024E/3048E:580X315X300MM
4048E/5048E//6048E:755X319X288MM
MODEL
(EP3000)		 HV Model
1012E 1024E 2012E 2024E 3024E 4048E 5048E 6048E
Line Mode Specifications:
Input Voltage Waveform Sinusoidal (utility or generator)
Nominal Input Voltage 230Vac(120VAC selectable)
Low Line Disconnect 184Vac±4%lusmn;4%lusmn;4%
Low Line Re-connect 194Vac ±4%lusmn;4%lusmn;4%
High Line Disconnect 265Vac±4%lusmn;4%lusmn;4%
High Line Re-connect 255Vac±4%lusmn;4%lusmn;4%
Max AC Input Voltage 270Vrms
Nominal Input Frequency 50Hz/ 60Hz (Auto detection)
Low Line Frequency Re-connect 58+0.3Hz for 60Hz;48+0.3Hz for 50Hz;
Low Line Frequency Disconnect 57+0.3Hz for 60Hz;47+0.3Hz for 50Hz;
High Line Frequency Re-connect 64+0.3Hz for 60Hz;54+0.3Hz for 50Hz;
High Line Frequency Disconnect
65+0.3Hz for 60Hz;55+0.3Hz for 50Hz;
Output Voltage Waveform As same as Input Waveform
Over-Load Protection(SMPSload) Circuit breaker
Output Short Circuit Protection Circuit breaker
Efficiency (Line Mode) >95%
Transfer Switch Rating 30A
Transfer Time (Ac to Dc) 10ms (typical)
Transfer Time (Dc to Ac) 10ms (typical)
Pass through without Battery Yes
Max Bypass Overload Current 30A
Invert Mode Specifications:
Output Voltage Waveform Sine wave
Rated Output Power (VA) 1000 2000 3000 4000 5000 6000
Rated Output Power (W) 1000 2000 3000 4000 5000 6000
Power Factor 0~1.0
Nominal Output Voltage (V) 230Vac
Nominal Output Frequency (Hz) 50Hz ± 0.3Hzn; 0.3Hzn; 0.3Hz
Auto tracking Main Frequency(Hz) Yes (Following Main first connection)50Hz @48-54Hz ;60Hz @58-64Hz
Output Voltage Regulation ±10% rms;10% rms;10% rms
Nominal Efficiency >80%

Over-Load Protection
(SMPS load)		 (110% 150% ±10%: Fault (shutdown output) after 20s;ter 20s;ter 20s;
Surge rating (10s) 3000VA 6000VA 9000VA 12000VA 15000 VA 18000VA
Capable of starting electric motor 1 HP 1 HP 2 HP 3 HP
Output Short Circuit Protection Current limit (Fault after 10s)
Bypass Breaker Size 30A 30A 30A 35A 50A
Nominal DC Input Voltage 12V 24V 12V 24V 24V 48V 48V
Min DC start voltage 10V/20V/40V
Low Battery Alarm 10.5Vdc ± 0.3Vdc for 12V battery;21.0Vdc ± 0.6Vdc for 24V battery;42.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Low DC input Shut-down 10.0Vdc ± 0.3Vdc for 12V battery;20.0vdc± 0.6Vdc for 24V battery;40.0Vdc± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Alarm & FaultFaultFault 16Vdc ± 0.3Vdc for 12V battery;32Vdc ± 0.6Vdc for 24V battery; 64Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Recovery 15.5Vdc ± 0.3Vdc for 12V battery;31.0Vdc ± 0.6Vdc for 24V battery; 62.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Power saver Load ≤25W (Enabled on 'P/S auto' setting of Remote control)emote control)rol)
Charge Mode Specifications:
Nominal Input Voltage 230Vac
Input Voltage Range 196~243Vac
Nominal Output Voltage According to the battery type
Nominal Charge Current 35A 35A 65A 35A 45A 35A 40A 50A
Charge Current Regulation ± 5Adcmn; 5Adcmn; 5Adc
Battery initial voltage 0 -15.7 Vdc (can operate with 0V battery)
Charger Short Circuit Protection Circuit breaker
Over Charge Protection Bat. V ≥15.7Vdc/31.4Vdc,beeps 0.5s every 1s & fault after 60sfter 60sfter 60s
General Specifications
Safety Certification CE
Safety Certification FCC
Operating Temperature Range 0°C to 40°C 40°Ceg;C 40°C
Storage temperature 15°C below zero to 60°C 60°Ceg;C 60°C
Operation humidity 5% to 95%
Audible Noise 60dB max
Cooling Forced air, variable speed fan
Size 1012E/1024E/2012E/2024E/2048E/3012E/3024E/3048E:580X315X300MM
4048E/5048E//6048E:755X319X288MM
MODEL
(EP3000)		 HV Model
1012E 1024E 2012E 2024E 3024E 4048E 5048E 6048E
Line Mode Specifications:
Input Voltage Waveform Sinusoidal (utility or generator)
Nominal Input Voltage 230Vac(120VAC selectable)
Low Line Disconnect 184Vac±4%lusmn;4%lusmn;4%
Low Line Re-connect 194Vac ±4%lusmn;4%lusmn;4%
High Line Disconnect 265Vac±4%lusmn;4%lusmn;4%
High Line Re-connect 255Vac±4%lusmn;4%lusmn;4%
Max AC Input Voltage 270Vrms
Nominal Input Frequency 50Hz/ 60Hz (Auto detection)
Low Line Frequency Re-connect 58+0.3Hz for 60Hz;48+0.3Hz for 50Hz;
Low Line Frequency Disconnect 57+0.3Hz for 60Hz;47+0.3Hz for 50Hz;
High Line Frequency Re-connect 64+0.3Hz for 60Hz;54+0.3Hz for 50Hz;
High Line Frequency Disconnect
65+0.3Hz for 60Hz;55+0.3Hz for 50Hz;
Output Voltage Waveform As same as Input Waveform
Over-Load Protection(SMPSload) Circuit breaker
Output Short Circuit Protection Circuit breaker
Efficiency (Line Mode) >95%
Transfer Switch Rating 30A
Transfer Time (Ac to Dc) 10ms (typical)
Transfer Time (Dc to Ac) 10ms (typical)
Pass through without Battery Yes
Max Bypass Overload Current 30A
Invert Mode Specifications:
Output Voltage Waveform Sine wave
Rated Output Power (VA) 1000 2000 3000 4000 5000 6000
Rated Output Power (W) 1000 2000 3000 4000 5000 6000
Power Factor 0~1.0
Nominal Output Voltage (V) 230Vac
Nominal Output Frequency (Hz) 50Hz ± 0.3Hzn; 0.3Hzn; 0.3Hz
Auto tracking Main Frequency(Hz) Yes (Following Main first connection)50Hz @48-54Hz ;60Hz @58-64Hz
Output Voltage Regulation ±10% rms;10% rms;10% rms
Nominal Efficiency >80%

Over-Load Protection
(SMPS load)		 (110% 150% ±10%: Fault (shutdown output) after 20s;ter 20s;ter 20s;
Surge rating (10s) 3000VA 6000VA 9000VA 12000VA 15000 VA 18000VA
Capable of starting electric motor 1 HP 1 HP 2 HP 3 HP
Output Short Circuit Protection Current limit (Fault after 10s)
Bypass Breaker Size 30A 30A 30A 35A 50A
Nominal DC Input Voltage 12V 24V 12V 24V 24V 48V 48V
Min DC start voltage 10V/20V/40V
Low Battery Alarm 10.5Vdc ± 0.3Vdc for 12V battery;21.0Vdc ± 0.6Vdc for 24V battery;42.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Low DC input Shut-down 10.0Vdc ± 0.3Vdc for 12V battery;20.0vdc± 0.6Vdc for 24V battery;40.0Vdc± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Alarm & FaultFaultFault 16Vdc ± 0.3Vdc for 12V battery;32Vdc ± 0.6Vdc for 24V battery; 64Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Recovery 15.5Vdc ± 0.3Vdc for 12V battery;31.0Vdc ± 0.6Vdc for 24V battery; 62.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Power saver Load ≤ 25W (Enabled on 'P/S auto' setting of Remote control)emote control)rol)
Charge Mode Specifications:
Nominal Input Voltage 230Vac
Input Voltage Range 196~243Vac
Nominal Output Voltage According to the battery type
Nominal Charge Current 35A 35A 65A 35A 45A 35A 40A 50A
Charge Current Regulation ± 5Adcmn; 5Adcmn; 5Adc
Battery initial voltage 0 -15.7 Vdc (can operate with 0V battery)
Charger Short Circuit Protection Circuit breaker
Over Charge Protection Bat. V ≥ 15.7Vdc/31.4Vdc,beeps 0.5s every 1s & fault after 60sfter 60sfter 60s
General Specifications
Safety Certification CE
Safety Certification FCC
Operating Temperature Range 0°C to 40°C 40°Ceg;C 40°C
Storage temperature 15°C below zero to 60°C 60°Ceg;C 60°C
Operation humidity 5% to 95%
Audible Noise 60dB max
Cooling Forced air, variable speed fan
Size
1012E/1024E/2012E/2024E/2048E/3012E/3024E/3048E:580X315X300MM
4048E/5048E//6048E:755X319X288MM

About inverter installation:

About us:


Pls contact Vena Tang:
Tel: +86 755 2910 1183