Pure Sine Wave Inverter 1kw 2kw 3kw 4kw5kw 6kw

Pure Sine Wave Inverter 1kw 2kw 3kw 4kw5kw 6kw

纯正弦波逆变器1kw 2kw 3kw 4kw5kw 6kw

180-450 USD

加入意向
型号。 纯正弦波逆变器1〜6KW / 12V或24V或48V
证明 ccc，iso9001，ce，saa
电路拓扑 全桥型
类型 直流/交流逆变器
充电电流 最大70amp
输出波 纯正弦波
发电机兼容 很好匹配
标称输入电压 230VAC（155-265V）（120VAC可选：100-127V）
商标 必须或者是
规范 CE和SONCAP证书
HS编码 8504403090
源流的性质 主动变频器
输出功率 >1000W
波弦的性质 正弦波逆变器
容量 1000W-6000瓦特
DC 12V / 24V / 48V可选
变形金刚 是的，纯Cooper
在电池充电器 是的，可调节的充电电流
证书 ce soncap iso9001 2008
运输包装 纸箱或外部木岩
起源 中国深圳
主要特点：
内置起动控制电路，用于二线和三线发电机起动系统
简单的控制与一个卡扣式盖子，保护设置不被意外更改
更好的热性能使全功率输出功率达到50°C（122°F），而不降低额定值de-rating
高浪涌能力开始更困难的负载，并可靠地处理过载条件
耐磨粉末涂层，耐腐蚀钢底盘
70安全自动三级电池充电器（散装，吸收和浮动）和电池均衡与远程温度传感器，以提高性能
逆变器图片：
模型
（ep3200）		 EP模型
1012 1024 2012 2024 3024 4048 5048 6048
线路模式规格：
输入电压波形 正弦（效用或发电机）
标称输入电压 230Vac（可选）
低线断开 155Vac±4％lusmn; 4％lusmn;4%
低线重新连接 164Vac±4％lusmn; 4％lusmn;4%
高线断开 272Vac±4％lusmn; 4％lusmn;4%
高线重新连接 265VAC±4％lusmn; 4％lusmn;4%
最大交流输入电压 270Vrms
标称输入频率 50Hz / 60Hz（自动检测）
低线频率重新连接 60Hz时为58 + 0.3Hz; 50Hz为48 + 0.3Hz;
低线频率断开 60Hz为57 + 0.3Hz，50Hz为47 + 0.3Hz;
高线频率重新连接 60Hz为64 + 0.3Hz，50Hz为54 + 0.3Hz;
高线频率断开
60Hz为65 + 0.3Hz; 50Hz为55 + 0.3Hz;
输出电压波形 与输入波形相同
过载保护（SMPSload） 断路器
输出短路保护 断路器
效率（线路模式） >95%
转换开关额定值 30A
转移时间（Ac到Dc） 10ms（典型值）
转移时间（Dc到Ac） 10ms（典型值）
充电电流 电流可调25％50％75％100％（可选）
最大旁路过载电流 1kw / 2k / 3kw：30A 4kw / 5kw / 6kw：40A
反转模式规格：
输出电压波形 纯正弦波
额定输出功率（VA） 1000 2000 3000 4000 5000 6000
额定输出功率（W） 1000 2000 3000 4000 5000 6000
功率因数 1.0
标称输出电压（V） 230V交流
额定输出频率（Hz） 50Hz±0.3Hzn; 0.3Hzn; 0.3Hz
自动跟踪主频率（Hz） 是（主要第一次连接）50Hz @ 48-54Hz; 60Hz @ 58-64Hz
输出电压调节 ±10％rms; 10％rms;10% rms
效率（电池模式） >90%

过载保护
（SMPS负载）		 (110%150％±10％：20s后故障（停机输出）;％：20s后故障（停机输出）ter 20s;
浪涌等级 3000VA 6000VA 9000va 12000va 15000 va 18000va
能启动电动机 1马力 1马力 2马力 3马力
输出短路保护 电流限制（10s后故障）
旁路断路器尺寸 10A 30A 30A 30A 30A
标称直流输入电压 12V 24V 12V 24V 24V 48V 48V
最小直流启动电压 11V / 22V / 43V
低电量报警 10.5Vdc±0.3Vdc为12V电池; 21.0Vdc±0.6Vdc为24V电池; 42.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
低直流输入关断 10.0Vdc±0.3Vdc为12V电池; 20.0vdc±0.6Vdc为24V电池; 40.0Vdc±0.6Vdc为48V电池0.6Vdc为48V电池0.6Vdc for 48V battery
高直流输入报警和故障缺陷Fault 16Vdc±0.3Vdc，12V电池; 32Vdc±0.6Vdc，24V电池; 64Vdc±0.6Vdc，48V电池0.6Vdc，48V电池0.6Vdc for 48V battery
高直流输入恢复 15.5Vdc±12V电池为±0.3Vdc; 24V电池为31.0Vdc±0.6Vdc; 62.0Vdc±0.6Vdc，48V电池，0.6Vdc，48V电池0.6Vdc for 48V battery
省电器 负载≤25W; 25W;25W
充电模式规格：
标称输入电压 230V交流
输入电压范围 155-265Vac
标称输出电压 与输入电压相同
标称充电电流 35A 35A 70A 35A 45A 35A 40A 50A
充电电流调节 ±5Adcmn; 5Adcmn; 5Adc
电池初始电压 0 -15.7 Vdc（可以使用0V电池）
充电器短路保护 断路器
过充电保护 蝙蝠。 V≥15.7Vdc/ 31.4Vdc，60s后60s，每1s发生嘟嘟声0.5sfter 60s
一般规格
安全认证 CE / SONCAP
安全认证 FCC
工作温度范围 0°C至40°C 40°Ceg;C 40°C
储存温度 15°C低于零至60°C 60°Ceg;C 60°C
工作湿度 5％至95％
声音噪音 最大60dB
冷却 强制空气，变速风扇
尺寸 1012/1024/2012/2024/2048/3012/3024/3048：580x315x300mm
五千○四十八分之四千○四十八// 6048：755x319x288mm
Model NO. pure sine wave inverter 1- 6KW/12V or 24V or 48V
Certification CCC, ISO9001, CE, SAA
Circuit Topologies Full-Bridge Type
Type DC/AC Inverters
Charging Current Max 70AMP
Output Wave Pure Sine Wave
Generator Compatible Very Well Match
Nominal Input Voltage 230VAC(155-265V)(120VAC Selectable: 100-127V)
Trademark MUST or OEM
Specification CE and SONCAP certificate
HS Code 8504403090
Nature of Source Flow Active Inverter
Output Power >1000W
Nature of Wave String Sine Wave Inverter
Capacity 1000W-6000W
DC 12V/24V/48V Optional
Transformer Buit in Yes, Pure Cooper
Buit in Battery Charger Yes, Adjustable Charging Current
Certificates CE Soncap ISO9001 2008
Transport Package Cartons or With Outside Wooden Rock
Origin Shenzhen, China
Main Features:
Built-in starting control circuits for two- and three-wire generator starting systems
Simplified controls with a snap-on cover that protects settings from being accidentally changed
Better thermal performance allows full output power to 50° C (122° F) without de-rating de-ratingde-rating
High surge capacity starts more difficult loads and handles overload conditions reliably
Durable powder coated, corrosion resistant steel chassis
70-amp automatic three-stage battery charger (bulk, absorption, and float) and battery equalization with remote temperature sensor for increased performance
Inverter pictures:
MODEL
(EP3200)		 EP Model
1012 1024 2012 2024 3024 4048 5048 6048
Line Mode Specifications:
Input Voltage Waveform Sinusoidal (utility or generator)
Nominal Input Voltage 230Vac( selectable)
Low Line Disconnect 155Vac±4%lusmn;4%lusmn;4%
Low Line Re-connect 164Vac ±4%lusmn;4%lusmn;4%
High Line Disconnect 272Vac±4%lusmn;4%lusmn;4%
High Line Re-connect 265Vac±4%lusmn;4%lusmn;4%
Max AC Input Voltage 270Vrms
Nominal Input Frequency 50Hz/ 60Hz (Auto detection)
Low Line Frequency Re-connect 58+0.3Hz for 60Hz;48+0.3Hz for 50Hz;
Low Line Frequency Disconnect 57+0.3Hz for 60Hz;47+0.3Hz for 50Hz;
High Line Frequency Re-connect 64+0.3Hz for 60Hz;54+0.3Hz for 50Hz;
High Line Frequency Disconnect
65+0.3Hz for 60Hz;55+0.3Hz for 50Hz;
Output Voltage Waveform As same as Input Waveform
Over-Load Protection(SMPSload) Circuit breaker
Output Short Circuit Protection Circuit breaker
Efficiency (Line Mode) >95%
Transfer Switch Rating 30A
Transfer Time (Ac to Dc) 10ms (typical)
Transfer Time (Dc to Ac) 10ms (typical)
Charge current current is adjustable 25% 50% 75% 100%(option)
Max Bypass Overload Current 1kw/2k/3kw: 30A 4kw/5kw/6kw: 40A
Invert Mode Specifications:
Output Voltage Waveform pure sine wave
Rated Output Power (VA) 1000 2000 3000 4000 5000 6000
Rated Output Power (W) 1000 2000 3000 4000 5000 6000
Power Factor 1.0
Nominal Output Voltage (V) 230Vac
Nominal Output Frequency (Hz) 50Hz ± 0.3Hzn; 0.3Hzn; 0.3Hz
Auto tracking Main Frequency(Hz) Yes (Following Main first connection)50Hz @48-54Hz ;60Hz @58-64Hz
Output Voltage Regulation ±10% rms;10% rms;10% rms
Efficiency (battery mode) >90%

Over-Load Protection
(SMPS load)		 (110%150% ±10%: Fault (shutdown output) after 20s;%: Fault (shutdown output) after 20s;ter 20s;
Surge rating 3000VA 6000VA 9000VA 12000VA 15000 VA 18000VA
Capable of starting electric motor 1 HP 1 HP 2 HP 3 HP
Output Short Circuit Protection Current limit (Fault after 10s)
Bypass Breaker Size 10A 30A 30A 30A 30A
Nominal DC Input Voltage 12V 24V 12V 24V 24V 48V 48V
Min DC start voltage 11V/22V/43V
Low Battery Alarm 10.5Vdc ± 0.3Vdc for 12V battery;21.0Vdc ± 0.6Vdc for 24V battery;42.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Low DC input Shut-down 10.0Vdc ± 0.3Vdc for 12V battery;20.0vdc± 0.6Vdc for 24V battery;40.0Vdc± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Alarm & FaultFaultFault 16Vdc ± 0.3Vdc for 12V battery;32Vdc ± 0.6Vdc for 24V battery; 64Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
High DC input Recovery 15.5Vdc ± 0.3Vdc for 12V battery;31.0Vdc ± 0.6Vdc for 24V battery; 62.0Vdc ± 0.6Vdc for 48V battery0.6Vdc for 48V battery0.6Vdc for 48V battery
Power saver Load ≤25W;25W;25W
Charge Mode Specifications:
Nominal Input Voltage 230Vac
Input Voltage Range 155-265Vac
Nominal Output Voltage same as input voltage
Nominal Charge Current 35A 35A 70A 35A 45A 35A 40A 50A
Charge Current Regulation ± 5Adcmn; 5Adcmn; 5Adc
Battery initial voltage 0 -15.7 Vdc (can operate with 0V battery)
Charger Short Circuit Protection Circuit breaker
Over Charge Protection Bat. V ≥15.7Vdc/31.4Vdc,beeps 0.5s every 1s & fault after 60sfter 60sfter 60s
General Specifications
Safety Certification CE/SONCAP
Safety Certification FCC
Operating Temperature Range 0°C to 40°C 40°Ceg;C 40°C
Storage temperature 15°C below zero to 60°C 60°Ceg;C 60°C
Operation humidity 5% to 95%
Audible Noise 60dB max
Cooling Forced air, variable speed fan
Size 1012/1024/2012/2024/2048/3012/3024/3048:580X315X300MM
4048/5048//6048:755X319X288MM