10A Power Controller for Solar UPS
10A太阳能UPS电源控制器
| 型号。 | SNC-010 |
| 额定充电电流 | 10A |
| 公司 | 生产厂家 |
| 商标 | SNAT |
| 起源 | 广东佛山 |
| 应用 | 收集器控制器，热水器控制器，太阳能系统控制器，充电器控制器，照明控制器，风力控制器，太阳能工作站，电压控制器 |
| OEM / ODM | 接受 |
| 控制模式 | PWM |
| 规范 | CE; ISO9001 |
| HS编码 | 8537109090 |
产品介绍
专为太阳能发电系统设计的太阳能充电控制器系列产品，采用MCU智能控制技术，实现太阳能电池充放电管理，延长系统使用寿命
- 可广泛应用于家庭，学校，街道，工矿，边防，岛屿，牧区等太阳能供电系统
Charactistics
1, 采用单片机和专用软件 专业软件 基于专家控制系统，实现智能SOC控制
2，温度补偿使用外部温度传感器，精度更高 内置温度传感器控制
3,具有自动控制过充，放电，电子短路保护，过载保护， 独特的防反相连接保护，上述保护不会损坏任何零件和烧伤保险
4, 采用串联PWM充电主电路，使充电回路的电压损耗比使用二极管充电电路减少近一半，与PWM相比，充电效率高3％〜6％，增加电源使用时间;充放电恢复上升，正常直充电器，浮动自动控制方式使系统使用寿命更长，同时具有高精度温度补偿
5, 直观的LED发光管指示当前的电池状态，使用户了解状态
6,所有控制采用工业级芯片，可在冷，高温，潮湿的环境中自由运行，采用晶体定时控制，定时控制精度 与此同时
7, 使用数字LED显示屏和设备，一键式操作可以完成所有设置，非常方便
8, 通过多级单次加载时间设置，可以独立于双倍时间设置多级加载时间设置
9, 双重会话设置采用模糊控制自动识别，并根据实际更正夜间关闭加载时间（精确到分钟），确保负载只有在早晨变暗之后的设定时间打开。
技术参数
| 类型 | SNC-010 |
| 额定充电电流 | 10A |
| 额定负载电流 | 10A |
| 系统电压 | 12V。 * 2 / 24v自动 |
| 太阳能投入 | <25, x2/24V DCV DC |
| 120Wp，x2 / 24V | |
| 过载，短路保护 | 过载保护：1.25倍额定电流60s，1.5倍额定电流5s;短路保护：≥3倍额定电流rent |
| 空载损耗 | ≤15mA5 mA5 mA |
| 充电回路下降 | ≤0.26v.26v.26V |
| 放电回路下降 | ≤0.15v.15v.15V |
| 过电压保护 | 17V,×2 / 24vs; 2 / 24Vs;2/24V; |
| 工作温度 | 技术等级:-35ºCordm;Çordm;C 至 +55ºCordm;Çordm;C; |
| 升压电压 | 14.6V;×2 / 24vs; 2 / 24Vs;2/24V; （保持时间:30分钟）(只能用于过放电) |
| 直接充电电压 | 14.4V;×2 / 24vs; 2 / 24Vs;2/24V; （保持时间:30分钟） |
| 浮动充电 | 13.6V;×2 / 24vs; 2 / 24Vs;2/24V;（保持时间：直到下降到充电返回电压运动） |
| 充电回路电压 | 13.2v;×2 / 24Ves; 2 / 24Vs;2/24V; |
| 温度补偿 | -5mV /ºCordm;Çordm;C/2V(提升，直接，浮动，充电返回电压补偿); |
| 欠电压 | 12.0V;×2 / 24Ves; 2 / 24Vs;2/24V; |
| 过放电电压 | 11.1V- 初始放电电压d充电率c补偿校正（空载电压）;×2 / 24Ves; 2 / 24Vs;2/24V; |
| 过放电返回电压 | 12.6V;×2 / 24vs; 2 / 24Vs;2/24V; |
| 控制模式 | PWM |
任何要求，欢迎联系 刘小姐: 点击贸易信使; 电话：+86 757 81816131;手机：+86 18039293535。,
您将在12小时内收到我们的答复
| Model NO. | SNC-010 |
| Rated Charge Current | 10A |
| Company | Manufacturer |
| Trademark | SNAT |
| Origin | Foshan Guangdong |
| Application | Collector Controller, Water Heater Controller, Solar System Controller, Charger Controller, Lighting Controller, Wind Controller, Solar Working Station, Voltage Controller |
| OEM/ODM | Accept |
| Control Mode | PWM |
| Specification | CE; ISO9001 |
| HS Code | 8537109090 |
Product Introduction
The series products of solar charge controller designed for solar power generation system, uses the MCU intelligent control technology, implementation charge and discharge management for solar battery, prolong the service life of the system
- Can be widely used in family, school, street, industrial and mining, frontier defense, islands, pastoral areas such as solar energy power supply system
Charactistics
1, Using the single chip microcomputer and special software, adopted specialized software based on expert control system, realized intelligent SOC control
2,Temperature compensation used the external temperature sensor,precision is higher with a built-in temperature sensor control
3,Having automatic control for overcharge, discharge, electronic short circuit protection, overload protection, unique anti inversed connection protective, the above protection do not damage any parts and burn insurance
4, Adopted tandem PWM chargie main circuit, make the charging loop voltage loss reduce nearly half than using diode charging circuit, charging efficiency is high 3% ~ 6% compared with PWM and increases power use time;Had overdischarge recover ascension of charging, normal straight charger, floating automatic control method to make the system have a longer service life and a high precision temperature compensation at the same time
5, Intuitive LED luminous tube indicate the current battery status, make users comprehend the status
6,All control adopt the industrial-grade chip, can be run freely in cold, high temperature, damp environment, use the crystals timing control, timing control precision at the same time
7, Using digital LED display and equipment, one-click operation can complete all settings and very convenient
8, With multi-stage single time load time setting, and multistage load time setting can be set up independently of the double time
9, Double session Settings adopted fuzzy control automatic identification and according to the actual correction night shut down load time (accurate to the minutes) to ensure loads only open at set time after it gets darkthe before morning.
Technology Parameter
| Type | SNC-010 |
| Rated charge current | 10A |
| Rated load current | 10A |
| System voltage | 12V. *2/24V AUTO |
| Solar input | <25, x2/24V DCV DC |
| 120Wp, x2/24V | |
| Overload, short circuit protective | Overload protection: 1.25 times rated current 60s, 1.5 times rated current 5s; Short circuit protection: ≥3 times rated currentrentrent |
| No-load loss | ≤15 mA5 mA5 mA |
| Charge loop drop | ≤0.26V.26V.26V |
| Discharge loop drop | ≤0.15V.15V.15V |
| Over-voltage Protection | 17V,×2/24Vs;2/24Vs;2/24V; |
| Working temperature | Technical grade:-35ºCordm;Cordm;C to +55ºCordm;Cordm;C; |
| Boost voltage | 14.6V;×2/24Vs;2/24Vs;2/24V; (maintain time:30min)(only be used for overdischarge) |
| Direct charge voltage | 14.4V;×2/24Vs;2/24Vs;2/24V; (maintain time:30min) |
| Float charge | 13.6V;×2/24Vs;2/24Vs;2/24V;(Maintain time: until drop to charge return voltage motion) |
| Charge return voltage | 13.2v;×2/24Ves;2/24Vs;2/24V; |
| Temperature compensation | -5mv/ºCordm;Cordm;C/2V(lifting,direct, floating, charging return voltage compensation); |
| Undervoltage voltage | 12.0V;×2/24Ves;2/24Vs;2/24V; |
| Overdischarge voltage | 11.1V- Initial discharge voltage of discharge rate compensation correction(No-load voltage);×2/24Ves;2/24Vs;2/24V; |
| Overdischarge return voltage | 12.6V;×2/24Vs;2/24Vs;2/24V; |
| Control mode | PWM |
Any requirements, welcome to contact with Sabrina Liu: Click Trade messenger; Tel: +86 757 81816131; Mobile: +86 18039293535.,
You will get our reply in 12 hours
