H-3000 Mobile Medical Infant Warmer Incubator
H-3000移动医疗婴儿保温箱
| 型号。 | H-3000 |
| 理论 | 婴儿孵化器 |
| 组 | 婴儿 |
| Airtemp控制范围 | 20℃〜37℃立方厘米〜37℃下g;cc~37°c |
| 床垫托盘尺寸 | 630×360 Mms; 360 Mm;360 Mm |
| 皮肤温度传感器精度 | ≤0.3°C0.3℃下g;c0.3°c |
| 敞篷环境噪声水平 | ≤55db;55分贝55db |
| 包装尺寸 | 100×58×80 Cm（2箱）120kgsartons）120kgsrtons) 120kgs |
| 运输包装 | 木箱 |
| 起源 | 中国 |
| 功能 | 婴儿保温箱 |
| 证明 | ce，iso13485 |
| 温度控制模式 | 空气和皮肤伺服控制 |
| 操作端口 | 6（2个Iris Ports） |
| Skintemp控制范围 | 30℃〜37℃立方厘米〜37℃下g;cc~37°c |
| 湿度显示范围 | 5%~99% |
| RS-232connector | 是 |
| 商标 | Healicom |
| 规范 | 高质量 |
| HS编码 | 90189090 |
H-3000婴儿培养箱
标准组成：
伺服控制模式：空气温度，皮肤温度;
即时参数显示：设定温度，空气温度，皮肤温度，内部湿度，热功率;
声光报警：电源故障，传感器故障，更高和更低的温度，空气和皮肤温度超驰，风扇故障，系统故障;阀杆故障;stem failure;
> 37°C预设模式：电源故障复位存储器，报警静音，键盘锁定，自检功能;tion;
RS-232输出连接器（用于网络系统）
规范
功率
型号H-3000-1E: 110 / 120V交流，50Hz / 60Hz
型号H-3000-2E: 220 / 240V交流，50Hz / 60Hz
电源输入≤400VA00VA00VA
报警
电源（检测）失败
风扇故障
传感器报警
空气传感器故障
传感器不在位
皮肤传感器断开
皮肤传感器故障
偏差报警
高气温: 如果显示空气温度比设定点高15°C，则激活point
低气温: 如果显示空气温度比设定点低25°C，则激活point
高皮肤温度如果显示皮肤温度高于设定点10°Cpoint
低皮肤温度: 如果显示，激活皮肤温度比设定点低10°Cpoint
过温报警
空气过温: 显示时激活设定温度≤37°C时空气温度接近38°C，空气模式下设定温度> 37°C时空气温度接近40°C;空气模式下空气温度37°Cegt;37°C in Air Mode
超过皮肤温度: 显示时激活皮肤温度接近38°C，设定温度ature :在37°C的温度下，在皮肤模式下，在皮肤模式下，温度为37℃e°C in Skin Mode
系统报警
系统错误: 温度控制系统发生故障时激活
温度控制范围和相关规格
气温: 20°CDEG; C ^deg;C~37°C，设定温度≤37°C，37°C，37°C37°C°C, 37°C~39°C，设定温度> 37°C> 37°Ceg;C>37°C
皮肤温度: 20°CDEG; C ^deg;C~37°C，设定温度≤37°C，37°C，37°C37°C°C, 37°C~38℃，设定温度> 37℃> 37℃eg;C>37°C
升温时间 :≤30min0min0min
温度变化: ±05°Cusmn; 05℃下g;Cusmn;05°C
温度均匀性 :≤1℃; 1℃eg;C;1°C
皮肤传感器精度 :≤03°C03℃下eg;C03°C
湿度
湿度显示范围 : 5％RH~99％RH
环境要求
环境温度
工作温度范围: + 20°CDEG; C ^deg;C ~+ 30°C°Cg;C°C
存储温度范围: -40°CDEG; C ^deg;C ~+ 55°C°Cg;C°C
环境湿度
工作湿度范围: 30%~75%
商店湿度范围: 10%~100%
大气压力范围 : 700hPa~1060hPa
其他规格
敞篷环境噪声水平: ≤55dB（环境噪声低于45dB）45dB）5dB)
敞篷中的二氧化碳（CO2）水平: 当空气中的二氧化碳混合物以750ml / min的速度递送到床垫中心以上10cm处时，小于05％
床垫空气速度: 小于035m / s
婴儿床最大负荷: 10公斤
输血架最大载荷: 2公斤
机柜最大负载: 6公斤
“沉默键盘键”功能
按下此键使闹钟静音10分钟，如下所示：
偏差报警
传感器报警
风扇报警
出厂默认设置
温度控制模式空气温度模式
空气温度: 32°CDEG; C ^deg;C
皮肤设定温度: 34°CDEG; C ^deg;C
温度单位:°CDEG; C ^deg;C
注意： 打开检修面板或检修门，或使用孵化器内的用品或其他设备，可改变气流模式，可能会影响温度均匀性，温度变化，培养箱温度读数与中心床垫温度和皮肤温度的相关性.
| Model NO. | H-3000 |
| Theory | Infant Incubator |
| Group | Infant |
| Airtemp Control Range | 20°c~37°cc~37°cg;cc~37°c |
| Mattress Tray Size | 630×360 Mms;360 Mm;360 Mm |
| Skin Temp Sensor Accuracy | ≤0.3°c0.3°cg;c0.3°c |
| Noise Level Within Hood Environment | ≤55db;55db55db |
| Packing Size | 100×58×80 Cm(2 Cartons) 120kgsartons) 120kgsrtons) 120kgs |
| Transport Package | Wooden Carton |
| Origin | China |
| Function | Infant Warmer Incubator |
| Certification | CE, ISO13485 |
| Temperature Control Mode | Air and Skin Servo Control |
| Operate Port | 6 (2 Iris Ports) |
| Skintemp Control Range | 30°c~37°cc~37°cg;cc~37°c |
| Humidity Display Range | 5%~99% |
| RS-232connector | Yes |
| Trademark | Healicom |
| Specification | High quality |
| HS Code | 90189090 |
H-3000 Infant Incubator
STANDARD COMPOSITION:
Servo Control Mode: air temperature, skin temperature;
Instant Parameter Displaying: set temp, air temp ,skin temp, internal humidity ,heat power rate;
Audible & Visual Alarms: power failure, sensor failure, higher & lower temp, air& skin temp override, fan failure, system failure;stem failure;stem failure;
﹥37°C Preset Mode: power failure reset memory, alarm silence, keypad lock, self-test function;unction;tion;
RS-232 Output Connector (Use for network system )
SPECIFICATION
POWER
Model H-3000-1E: 110 / 120 V ac, 50Hz / 60Hz
Model H-3000-2E: 220 / 240 V ac, 50Hz / 60Hz
Power Input ≤400VA00VA00VA
ALARM
Power Failure
Fan Failure
Sensor Alarm
Air Sensor Failure
Sensor Out of Position
Skin Sensor Disconnected
Skin Sensor Failure
Deviation Alarm
High Air Temperature: Activated if displayed Air Temperature is 15°C above set pointpointpoint
Low Air Temperature: Activated if displayed Air Temperature is 25°C below set pointpointpoint
High Skin Temperature Activated if displayed Skin Temperature is 10°C above set pointpointpoint
Low Skin Temperature: Activated if displayed Skin Temperature is 10°C below set pointpointpoint
Over Temperature Alarm
Over Air Temperature: Activated when displayed Air Temperature was approach 38°C for set temperature ≤37°C, or approach 40°C for set temperature ﹥37°C in Air Modegt;37°C in Air Modeegt;37°C in Air Mode
Over Skin Temperature: Activated when displayed Skin Temperature was approach 38°C for set temperatureatureature :≤37°C, or approach 39°C for set temperature ﹥37°C in Skin Mode°C in Skin Modee°C in Skin Mode
System Alarm
System Failure: Activated if Temperature Control System malfunctions
TEMPERATURE CONTROL RANGE AND CORRELATIVE SPECIFICATIONS
Air Temperature: 20°Cdeg;Cdeg;C~37°C, for set temperature ≤37°C, 37°C°C, 37°C37°C°C, 37°C~39°C, for set temperature ﹥37°C>37°Ceg;C>37°C
Skin Temperature: 20°Cdeg;Cdeg;C~37°C, for set temperature ≤37°C, 37°C°C, 37°C37°C°C, 37°C~38°C, for set temperature ﹥37°C>37°Ceg;C>37°C
Temperature Rise Time :≤30min0min0min
Temperature Variability: ±05°Cusmn;05°Cg;Cusmn;05°C
Temperature Uniformity :≤1°C;1°Ceg;C;1°C
Skin Sensor Precision :≤03°C03°Ceg;C03°C
HUMIDITY
Humidity Display Range : 5%RH~99%RH
ENVIRONMENT REQUIREMENT
Environment Temperature
Operation Temperature Range: +20°Cdeg;Cdeg;C ~+30°C°Cg;C°C
Store Temperature Range: -40°Cdeg;Cdeg;C ~+55°C°Cg;C°C
Environment Humidity
Operation Humidity Range: 30%~75%
Store Humidity Range: 10%~100%
Atmospheric Pressure Range : 700hPa~1060hPa
OTHER SPECIFICATION
Noise Level Within Hood Environment: ≤55dB(Environment noise below 45dB)45dB)5dB)
Carbon Dioxide (CO2) Level within the Hood: Less than 05% when a mixture of CO2 in air is delivered at 750ml/min at a point 10cm above the center of the mattress
Air Velocity Over Mattress: less than 035m/s
Infant Bed Max Load: 10kg
Transfusion Shelf Max Load: 2kg
Cabinet Max Load: 6kg
FUNCTION OF ''SILENCE KEYSILENCE KEY
Make the alarm to be silence for 10 minutes by press this key, following:
Deviation Alarm
Sensor Alarm
Fan Alarm
FACTORY DEFAULT SETTINGS
Temperature Control Mode Air Temperature Mode
Air Set Temperature: 32°Cdeg;Cdeg;C
Skin Set Temperature: 34°Cdeg;Cdeg;C
Temperature Units:°Cdeg;Cdeg;C
NOTE: Open Access Panel or Access Door or the use of supplies or other equipment within the Incubator, which can alter the air flow pattern, may effect temperature uniformity, temperature variability, the correlation of the Incubator temperature reading to center mattress temperature and skin temperature.
