标准组成：
伺服控制模式：空气温度;
即时参数显示：设定温度，空气温度，热功率;
声光报警：电源故障，传感器故障，高温/低温，空气温度超驰，风扇故障;诱饵;lure;
电源故障复位存储器和自检功能;
双斜面罩：4个手动口
规范
功率
H-800-1E型：110 / 120V交流，50Hz / 60Hz
型号H-800-2E：220/240 V交流，50Hz / 60Hz
电源输入：≤400VA00VA00VA
参见IEC60601-1，本设备属于ClassI，BF型，运行连续
报警
电力报警
电源故障：如果孵化器的主电源出现故障或电源线与墙壁插座意外断开，请激活
风扇报警
风扇故障：风扇电机故障时激活
传感器报警
空气传感器故障：空气传感器故障，请参考使用单位
偏差报警
高气温：如果显示空气温度高于设定点15°Cpoint
低气温：如果显示空气温度比设定点低25°Cpoint
过温报警
过热温度：显示时空气温度在空气模式模式下接近38°C Mode
系统报警
系统故障：温度控制系统故障时激活
温度控制范围和相关规格
空气温度：20°C〜37°C37°Cg; C37° C
升温时间：≤30min0min0min
温度变化：±0.5°C; 0.5°Cg; C; 0.5° C
温度均匀度：≤1°C1°Cg; C1° C
环境要求
环境温度
工作温度范围：+ 20°C〜+ 30°C30°Cg; C30° C
存储温度范围：-40°C〜+ 55°C55°Cg; C55° C
环境湿度
工作湿度范围：30％〜75％
商店湿度范围：10％〜100％
大气压力范围：700hPa〜1060hPa
其他规格
噪音环境：≤55dB（环境噪音低于45dB）5dB）5dB)
罩内的二氧化碳（CO2）含量：空气中的二氧化碳混合物在床垫中心以上10厘米处以750毫升/分的速度递送时，小于0.05％
床垫空气速度：小于035m / s
婴儿床最大负荷：10kg
输血架最大负荷：2kg
出厂默认设置
温度控制模式空气温度模式
空气温度：32°C; Ceg; C
温度单位：°Ceg; Ceg; C
注意：打开检修面板或检修门，或使用孵化器内的用品或其他设备，可改变气流模式，可能会影响温度均匀性，温度变化，培养箱温度读数与中心床垫温度和皮肤温度的相关性

STANDARD COMPOSITION:
Servo Control Mode: Air temp;
Instant Parameter Displaying: Set temp, air temp, heat power rate;
Audible & Visual Alarms: Power failure, sensor failure, higher/lower temp, air temperature override, fan failure;lure;lure;
Power failure reset memory and self-test function;
Hood with dual slope: 4 hand-ports
SPECIFICATION
POWER
Model H-800-1E: 110 / 120 V ac, 50Hz / 60Hz
Model H-800-2E: 220 / 240 V ac, 50Hz / 60Hz
Power Input: ≤ 400VA00VA00VA
Refer to IEC60601-1, this equipment belongs to ClassI, Type BF Its operation is continuous
ALARM
Power Alarm
Power Failure: Activates if primary power to the Incubator fails or the power wire is accidentally disconnected from the wall receptacle
Fan Alarm
Fan Failure: Activates if Fan motor malfunctions
Sensor Alarm
Air Sensor Failure: Air Sensor malfunction, refer unit to service
Deviation Alarm
High Air Temperature: Activated if displayed Air Temperature is 15° C above set pointpointpoint
Low Air Temperature: Activated if displayed Air Temperature is 25° C below set pointpointpoint
Over Temperature Alarm
Over Air Temperature: Activated when displayed Air Temperature was approach 38° C in Air Mode Mode Mode
System Alarm
System Failure: Activated if Temperature Control System malfunctions
TEMPERATURE CONTROL RANGE AND CORRELATIVE SPECIFICATIONS
Air Temperature: 20° C~37° C37° Cg; C37° C
Temperature Rise Time: ≤ 30min0min0min
Temperature Variability: ± 0.5° C; 0.5° Cg; C; 0.5° C
Temperature Uniformity: ≤ 1° C1° Cg; C1° C
ENVIRONMENT REQUIREMENT
Environment Temperature
Operation Temperature Range: +20° C ~ +30° C30° Cg; C30° C
Store Temperature Range: -40° C ~ +55° C55° Cg; C55° C
Environment Humidity
Operation Humidity Range: 30%~75%
Store Humidity Range: 10%~100%
Atmospheric Pressure Range: 700hPa~1060hPa
OTHER SPECIFICATION
Noise Level Within Hood Environment: ≤ 55dB(Environment noise below 45dB)5dB)5dB)
Carbon Dioxide (CO2) Level within the Hood: Less than 05% when a mixture of CO2 in air is delivered at 750ml/min at a point 10cm above the center of the mattress
Air Velocity Over Mattress: Less than 035m/s
Infant Bed Max Load: 10kg
Transfusion Shelf Max Load: 2kg
FACTORY DEFAULT SETTINGS
Temperature Control Mode Air Temperature Mode
Air Set Temperature: 32° Ceg; Ceg; C
Temperature Units: ° Ceg; Ceg; C
NOTE: Open Access Panel or Access Door or the use of supplies or other equipment within the Incubator, which can alter the air flow pattern, may effect temperature uniformity, temperature variability, the correlation of the Incubator temperature reading to center mattress temperature and skin temperature