Electrical Nail Drill Manicure Tool Nail Glazing Machine
电动钻钉修指甲工具指甲釉机
| 型号。 | a12 |
| 分类 | 指甲保养 |
| 类型 | 指甲钻 |
| 额定功率输入 | 15W |
| 商标 | BT |
| 起源 | 广州 |
| 证明 | SGS |
| 身体的一部分 | 手指 |
| 打包 | 纸板箱 |
| 工作电压 | 直流0-18v |
| 规范 | 21 * 26 *10厘米 |
的规格 电动指甲修指甲工具指甲机 :
主电源和控制部分零件 part
额定电压范围：220-240v-50hz
额定功率输入：15w
输出额定电压：DC 0-18V
输出电流：1.0A
手机（电机）部件：
工作电压：DC 0-18V
额定电流：1.0A
空载速度：29000-3000rpm
负载速度：27000-28000rpm
说明：
不要太频繁地转动转向，否则会损坏磨头。
逆时针转动SPEED CONTROL，将磨头减速至最小，然后关闭主电源并切换到0。
操作后，将磨头放在主面板的顶部。
磨头正在运转时，切勿拉出便携式磨头的5针插头。
长时间闲置时，请断开电源。
任何未经授权的拆卸，禁止在任何故障情况下，请联系代理或授权维修中心，我们承诺迅速，高品质和令人满意的服务。
如果电源线损坏，必须由制造商，其服务代理人或类似人员更换，以避免危险。
除了指导或协助的安全责任外，该装置还没有准备好对身体虚弱，缓慢的反应或人（包括儿童）的精神障碍。
主电源和控制部分零件 part
额定电压范围：220-240v-50hz
额定功率输入：15w
输出额定电压：DC 0-18V
输出电流：1.0A
手机（电机）部件：
工作电压：DC 0-18V
额定电流：1.0A
空载速度：29000-3000rpm
负载速度：27000-28000rpm
说明：
不要太频繁地转动转向，否则会损坏磨头。
逆时针转动SPEED CONTROL，将磨头减速至最小，然后关闭主电源并切换到0。
操作后，将磨头放在主面板的顶部。
磨头正在运转时，切勿拉出便携式磨头的5针插头。
长时间闲置时，请断开电源。
任何未经授权的拆卸，禁止在任何故障情况下，请联系代理或授权维修中心，我们承诺迅速，高品质和令人满意的服务。
如果电源线损坏，必须由制造商，其服务代理人或类似人员更换，以避免危险。
除了指导或协助的安全责任外，该装置还没有准备好对身体虚弱，缓慢的反应或人（包括儿童）的精神障碍。
| Model NO. | a12 |
| Classify | Nail Care |
| Type | Nail Drill |
| Rated Power Input | 15W |
| Trademark | BT |
| Origin | Guangzhou |
| Certification | SGS |
| Body Part | Finger |
| Packaging | Carton |
| Working Voltage | DC 0-18V |
| Specification | 21*26*10cm |
The specification of Electrical Nail drill manicure tool nail glazing machine :
For main power supply&control part part part
Rated voltage range:220-240v-50hz
Rated power input:15w
Output rated voltage: DC 0-18V
Output current: 1.0A
For handpiece(motor) part:
working voltage:DC 0-18V
Rated current:1.0A
No load speed:29000-3000rpm
Load speed:27000-28000rpm
Instructions:
Don't change the turning directions too frequently,otherwise it will damage the grinding head.
Turn the SPEED CONTROL counterclockwise to decelerate the grinding head to the minimum before turning off and switch the main power source to 0.
After operation,put the grinding head on the top of the main panel.
While the grinding head is in operation,never pull out the 5-pin plug of the portable grinding head.
For long idle time,please disconnect the source power.
Any unauthorized disassembling of the prohibited.in case of any breakdown,please contact the agent or authorized repair center,we promise swift,high-quality and satisfactory service.
If the supply cord if damaged,it must be replaced by the manufacturer,its service agent or similarly persons in order avoid a hazard.
The apparatus is not ready for the physically weak,slow response or a mental disorder of persons(including children) to use,except in the security responsibility of the guidance or assistance.
For main power supply&control part part part
Rated voltage range:220-240v-50hz
Rated power input:15w
Output rated voltage: DC 0-18V
Output current: 1.0A
For handpiece(motor) part:
working voltage:DC 0-18V
Rated current:1.0A
No load speed:29000-3000rpm
Load speed:27000-28000rpm
Instructions:
Don't change the turning directions too frequently,otherwise it will damage the grinding head.
Turn the SPEED CONTROL counterclockwise to decelerate the grinding head to the minimum before turning off and switch the main power source to 0.
After operation,put the grinding head on the top of the main panel.
While the grinding head is in operation,never pull out the 5-pin plug of the portable grinding head.
For long idle time,please disconnect the source power.
Any unauthorized disassembling of the prohibited.in case of any breakdown,please contact the agent or authorized repair center,we promise swift,high-quality and satisfactory service.
If the supply cord if damaged,it must be replaced by the manufacturer,its service agent or similarly persons in order avoid a hazard.
The apparatus is not ready for the physically weak,slow response or a mental disorder of persons(including children) to use,except in the security responsibility of the guidance or assistance.
