mabw-200尿液分析仪

这种尿液分析仪是专门用于尿液检测的
MABW-200尿液分析系统
8个项目，10个项目和11个项目测试条供选择;
热敏打印机或针式打印机可供选择;
尿液的颜色和清除率可用;
也有13个项目（含肌酸和钙）
3.1启动分析仪：安装分析仪时，打开电源开始;仪器将开始自检。仪器通过自检后，仪器处于工作状态，显示主画面。
3.2检查阶段：在开始任何测试之前，您应该首先检查舞台，看看它是否干净，或者如果装载平台和白色校准瓷砖是否干净，是否有任何异物。如果您注意到它们不干净，请参阅有关尿液分析仪维护和修理的手册。
3.3单条测试模式：按开始按钮，仪器警报提示蜂鸣声浸入尿液中，倒计时将从63秒开始（对于8个量油尺测试，倒计时将从33秒开始），取出测试条，然后完全浸入浸入患者尿液1-2秒钟，然后取出条带使用清洁纸去除多余的尿液，然后将条带放在装载平台上，以达到顶部狭槽。
3.4连续条带测试模式：连续测试时，倒计时从“32”开始（8次量油测试从3开始），仪器发出哔声后，将第二个条带浸入尿液中，然后放入在吸水纸上，等待下一个哔声。当仪器再次发出哔声准备第三条时，也将第二条测试条准备在装载平台上等，以完成连续操作。在连续测试模式下，在测试结束时，必须从仪器中取出板形，以使仪器自动停止，否则仪器将一次又一次地测试相同的条。再次。
3.5灰色条测试：灰条是用于测试尿液稳定性的标准固定吸光度。它可以直接在机器上测试。本试验过程中不允许将水或尿液放在板上，试验结果应符合“灰色条测试值”的要求，如果不接触本服务，则不作任何规定。

MABW-200 Urine Analyzer CE OEM ISO

This Urine Analyzer is specialy for urine test
MABW-200 urine analysis system
8 items, 10 items and 11 items test strips are for choice;
Thermal printer or needle printer is for choice;
Color and clearance of urine are available;
13 items are also available (Creatine and Calcium included)
3.1 Starting the analyzer: When the analyzer is installed, turn on the power to begin; The instrument will begin a self-test. After the instrument has been through the self-test, the instrument is in the working state, it displays the main screen.
3.2 Check the stage: Before starting any test you should first check the stage to see if it is clean or if there is any foreign things see if the loading platform and the white calibration tile are clean or not. If you do notice that they are not clean, refer to a manual about urine analyzer maintenance and repair.
3.3 Single strips test mode: Press the Start button, the instrument alert beep dipped into the urine, the countdown will start from 63 seconds (for 8 dipstick test the countdown will start from 33 seconds), remove the test strip and then immerse it completely immersed into the patient urine for 1-2 seconds, then remove the strips use a cleaning paper to remove excess urine and then put the strips on the loading platform in such a way to reach the top slot.
3.4 Continuous strip test mode: In case of continuous testing, the countdown will start from '32'(for 8 dipstick test it will start from 3), after the instrument beeps, prepare the second strip by immerse it in the urine and then put on the absorbent paper and wait for the next beep. When the instrument beeps again prepare the third strip, also put the second test strip prepared on the loading platform, and so on to complete a continuous operation. In Continuous test mode, at the end of the test you will have to remove the plate-form from the instrument so that the instrument stops automatically, otherwise, the instrument will go on testing the same strips over and over again. over again.
3.5 Gray bar test: Gray bar is the standard fixed-absorbance used to test the stability of urine. It can be test directly on the machine. It is not permit to put water or urine on the plate-form during this test the test results should the same according to the 'gray bar test value' line, if not contact the service.the service.