医用氧气调节器详细说明（系列）
输入压力：15Mpa
2.输出压力：0.2-0.3Mpa
3.安全阀自动排气压力：0.35 + _0.05Mpa
流量范围：1-15L / min
5.连接螺纹：G5 / 8，公头
主体：铜
7.结构：活塞式
8.包装：20PCS / CTN（彩盒）等
g。 W上。 / N。 w。20 / 19kg
尺寸：51×42×56cm2×56cm; 56cm2× 56cm
医用氧气调节器
具有加湿器的流量计用于降低气体压力并调节气体体积，救援患者并作为医院的氧疗治疗。也可以利用其他气体减压和控制流。
产品主要特点：
产品具有艺术气氛，流量控制舒适稳定。
减速器可调;结构独特，性能可靠。
不锈钢浮子和橙色底盘流量计具有特别的视觉效果;
国际标准连接方式，适用于各种气瓶安装。
适用范围
为缺氧的人提供氧气，用于急救或吸氧。
如何使用
1.连接进气口的螺母后，打开氧气瓶的阀门。
2.将氧气管连接到氧气出口。
3.卸下加湿杯（反时针旋转），将一些蒸馏水放入（净水或普通开水也可以发生），水量应在底部和顶部刻度之间，然后拧紧瓶盖到加湿杯（顺时针旋转）。
4.按照需要的速度旋转流量调节阀（逆时针向上，顺时针向下，直到关闭），然后将其放在鼻子上使用。
5.首先关闭氧气瓶的阀门，不要使用，然后关闭流量调节阀，直到氧气压力计的指针返回到零。
注意
1.确保连接器上没有灰尘，检查螺纹，然后安装吸入器。
2.确保流量计垂直于地板，流量调节阀关闭，然后缓慢打开氧气瓶阀门，调节高压表后显示氧气瓶压力的流量。
3.无剧烈冲击，远离腐蚀性物质，无油渍。
4.安全阀的固定螺丝不能随意旋转，非专业人员不得下车。
储存条件
应保存在湿度小于90％的环境中，无腐蚀性气体和腐蚀性气体。
质量保证期
在公司生活当天不能正常工作的一半年内，我们将修理或更换氧气吸入器，应符合贮存和使用规定。
规范
1.禁止使用浮标式氧气调节器进行氧气雾化处理。
禁止自己下车。

Detailed Description of Medical Oxygen Regulator (series)
1. Input pressure: 15Mpa
2. Output pressure: 0.2-0.3Mpa
3. Automatic Discharge Pressure of The Safety Valve: 0.35+_0.05Mpa
4. The Range of Flow: 1-15L/min
5. Connection Thread: G5/8, male
6. Mainbody: Copper
7. Structure: Piston type
8. Packing: 20PCS/CTN (color box) or other
9. G. W. /N. W.: 20/19kg
10. Dimension: 51× 42× 56cm2× 56cm; 56cm2× 56cm
Medical Oxygen Regulator
The flowmeter with humidifier is used in reducing gas pressure and adjusting the gas volume, which rescue patient and treat as oxygen therapy by hospital. Also may make using of other gas reduced pressure and the control flow.
Product main feature:
The product has artistic outlook, and flow control comfortable and stable.
The reductor is adjustable; The structure is unique, and the performance is reliable.
The stainless steel floater and the orange substrate flowmeter have a especially visual effect;
The international standard connect way, is suitable for all kinds of gas bottle installation.
Range of application
Give oxygen for first-aid or oxygen uptake for the people who are lack of oxygen.
How to use
1. Open the valve of oxygen cylinder after connect the screw nut of air intake closely.
2. Connect the oxygen pipe to the oxygen outlet firmly.
3. Demount the humidifying cup(anti clock wise rotation), put some distilled water in (purified water or plain boiled water can also take place), the water quantity should be between the bottom and top tick mark, then tighten up the bottle cap to the humidifying cup(clockwise rotation).
4. Rotate the flow regulating valve to the rate you need (anti clockwise to up, clockwise to down, till to close), then put it to nose to use.
5. Close the valve of oxygen cylinder firstly while not using, then close the flow regulating valve until the pointer of oxygen manometer return to zero.
Attention
1. Make sure there is no ash on the connector and check the screw thread, then install the inhalator.
2. Make sure the flow meter is vertical to the floor and flow regulating valve is closed, then open the valve of oxygen cylinder slowly, regulate the flow after the high pressure gauge shows the pressure of the oxygen cylinder.
3. No drastic shock, far away with the corrosive substance, and no oil stain.
4. The set screw of the safety valve can't be rotated at random, non-professional people are forbidden to dismount.
Condition for storage
Should be kept in the environment whose humidity is less than 90%, no corrosive gas and drafty.
Quality guarantee period
We will fix or change the oxygen inhalator within a half and a year after the day of living the company when it can't proper functioning, it should be under the condition of obeying the rule of storage and using.
Specification
1. Forbid to use the Buoy Type Oxygen Regulator to take oxygen atomization treatment.
2. Forbid to dismount by yourself.