多用途操作台，侧控（型号MSLMO10）


1，概述
A）主要用途：多用途操作台用于临床操作使用。
B）结构：通过油泵的平均液压方式进行升降运动，前后倾斜，桌面左右倾斜。背板由高压气瓶升高和降低。它具有安全的基座，美观的外形，防水防尘的功能，稳定实用，基座型号容易使医生靠近患者，减少疲劳。


2，规格

桌面尺寸：
总长... 2100mm
宽度... 500mm

部分尺寸：
头枕... 500×250mm
后段... 500×465mm
肾桥... 500×80mm
座椅段... 500×550mm
腿部... 600×240mm

地板上：
最大高度... 1000mm
最小高度... 700mm
上升距离...≥300 mm
运动范围：
Max Reversed Trendelenburg ...≥20°
Max Trendelenburg ...≥15°
最大横向倾斜...≥15°

章节调整：
头枕从水平升起...≥45°
头枕从水平位置下降...≥90°
背部从水平方向升起...≥60°
背部从水平面下降...≥30°
腿部从水平下降...≥90°
腿部打开...≥90°
肾桥高程≥100mm





注意事项：
1）床由机械和液压系统组成。合格专业人员在发生故障时检修机器。
2）当位置调整到极限时，电阻显着增加。所以它不能在这个时候拉硬，并应该向相反的方向回滚。
3）头枕调整采用严格的门锁。如果头枕的位置需要调整，则必须首先将头锁杆分开并调整到合适的位置，松开，否则容易损坏。
4）应在每个活动部位添加润滑油，以便床身操作方便，延长使用寿命。在床的每一侧和桌子下面的架子上的附件的轨道上涂抹凡士林，从而防止其生锈。
5）在使用前，应检查所有附件是否牢固锁定，以防止其在使用时脱落或滑落。
6）由于床有很多部件，保持所有的配件良好的秩序。
7）每次操作后，清洁床上的污垢，保持床和配件清洁，延长他们的生活。
8）地面必须保持干燥。虽然地板是洗涤和擦洗，请尽量不要
9）必须每年定期修理和保持清洁。
10）在临床使用中，手术台的侧倾角大于8度（标准等于或大于20度），用户认为，
患者从桌面落下，选择身体框架和身体带等，以确保使用安全。

Multi-purpose Operation Table, Side-controlled (Model MSLMO10)


1, General Description
A) Main Usage: Multi-purpose Operation Table is for clinical operating use.
B)Structure: Both the ascending and descending movements, the front and back lean and the left and right lean of the table top are carry on hydraulically by the mean of oil pump. The backboard is raised and lowered by the high pressure gas cylinder. It have the airproof pedestal, beautiful shape, waterproof and dustproof function, and it is stable and practical, the pedestal model is easy for physicians to close to sufferer and reduce fatigue.


2, Specifications

Dimensions of Table Top:
Overall length...2100mm
Width...500mm

Dimensions of Sections:
Head Rest...500× 250mm
Back Section...500× 465mm
Kidney Bridge...500× 80mm
Seat Section...500× 550mm
Leg Section...600× 240mm

Table Top from Floor:
Max Height...1000mm
Min Height...700mm
Rising Distance...≥ 300 mm
Range of Movements:
Max Reversed Trendelenburg...≥ 20°
Max Trendelenburg...≥ 15°
Max Lateral Tilt...≥ 15°

Adjustments of Sections:
Head-Rest raised from the horizontal...≥ 45°
Head-Rest lowered from the horizontal...≥ 90°
Back-Section raised from the horizontal...≥ 60°
Back-Section lowered from the horizontal...≥ 30°
Leg-Section lowered from the horizontal...≥ 90 °
Leg-Section opened...≥ 90°
Kidney Bridge Elevation...≥ 100mm





Cautions:
1)The bed is composed of mechanical and hydraulic systems. Qualified professionals Overhaul the machine when breakdowns happen.
2)When position is adjusted to the limit, the resistance increases significantly. So it can not be to pull hard at this time, and should be rolled back towards the opposite direction.
3)The Head-rest adjustment is adopted by a strict tecth lock. If the position of the head-rest needs adjusting, the tecth lock pole must be first separated and adjusted to suitable position, the got loose, otherwise it is easily damaged.
4)Lubricating oil should be added to every active part, so that the bed can be operated easily and prolong their life. Smear Vaseline over the tracks of the accessories on each side of the bed and the racks under the table, thus preventing it from being rusty.
5)Before putting into use, all attachments should be checked to see if they are locked securely so as to prevent them from loosing or sliding off while used.
6)As the bed has many parts, keep all the accessories in good order.
7)After operating every time, clean the dirt on the bed, keep the bed and accessories clean and prolong their life.
8)The ground must be kept dry. While the floor is washed and scrubed, please try not to
9)It must be repaired and kept clean regularly once a year.
10)In the clinical use, the lateral lean angle of the operating table is bigger than 8 degrees (the standard is equal or bigger than 20 degrees), the user shoud think the possibility that the
Patient falls from the table top, and selects a body frame and body belt and so on to ensure the use safety.