Ce Approved AIO-10B Medical Syringe Infusion Pump
Ce批准的AIO-10B医用注射器输液泵
| 型号。 | AIO-10B |
| 医疗器械监管类型 | 类型2 |
| 证书 | ce iso |
| 注射器尺寸 | 5 / 6ml，10 / 12ml，20 / 25ml，30 / 35ml，50 / 60ml |
| 输液范围 | 0.1ml〜9999.9ml，原值为0.1ml |
| 志愿 | 0.1〜5毫升/ H |
| 电击保护 | I类，CF型 |
| 规范 | ce iso |
| HS编码 | 8413190000 |
| 医疗器械注册/记录号 | Hsyjxz20132540393 |
| 电源 | ac 100v〜ac 242v，50 / 60hz |
| 内置电池 | DC 12V 1800mAh，Ni-MH，可充电 |
| 流量选择 | 0.1ml / H〜1600ml / H，原值为0.1ml / H |
| 流量精度 | ±3％plusmn; 3％lusmn;3% |
| 防水等级 | IPX4 |
| 商标 | healicom |
| 起源 | 中国江苏 |
基本参数
| 项目 模型 | AIO-10B | AIO-10C |
| 尺寸（mm） | 354（L）×132（宽）×199（H）×199（H）199(H)×199(H) | 354（L）×132（宽）×268（H）×268（H）268(H)×268(H) |
| 重量 | 2.7公斤 | 3.6公斤 |
| 电池连续使用时间 | 约6小时 （充满电的新电池，运行速度为5ml / h） | 约5小时 （充满电的新电池，运行速度为5ml / h） |
| 额定消耗 | ≤25va5 va5 VA | ≤35va5 va5 VA |
规范
| 电源 | ac 100v〜ac 242v，50 / 60hz |
| 内置电池 | DC 12V 1800mAh，镍氢充电 |
| 输液流选择 | 0.1ml / h〜1200ml / h（1-150d / min），原值为0.1ml / h（1d / min） |
| 注射器流量选择 | 0.1ml / h〜1600ml / h，原值为0.1ml / h |
| 注射器尺寸 | 5 / 6ml，10 / 12ml，20 / 25ml，30 / 35ml，50 / 60ml |
| 螺栓率 | 注射器50ml：1600ml / h 注射器30ml：900 ml / h 注射器20ml：600ml / h 注射器10ml：400ml / h 注射器5ml：200ml / h |
| 输液范围 | 0.1ml〜9999.9ml，原值0.1ml |
| 输液精度 | 体积模式±5％，下降模式±2d模式±2dusmn;2dmode ±2d |
| 注射器流速精度 | ±3％lusmn; 3％lusmn;3% |
| 志愿 | 0.1〜5毫升/ h的 |
| 闭塞压力 | 高：110kPa±20kPa（825mmHg±150mmHg）lusmn; 150mmHg）lusmn;150 mmHg) 中间：为80kPa±30kPa时（600mmHg±225mmHg）plusmn; 225mmHg）plusmn;225mmHg) 低：60kPa±20kPa（450mmHg±150mmHg）lusmn; 150mmHg）lusmn;150 mmHg) 最大输出压力：< 975mmHg(130kPa)kPa) |
| 使用环境 | 温度：5ºC〜43ºCCC〜43ºCrdm;CC~43ºC 相对湿度：≤90％RH（无冷凝状态）tus）tus) 大气压：860hPa〜1060hPa |
| 存储环境 | 温度：-20℃〜+ 55℃〜+55ºCrdm;C~+55ºC 相对湿度：≤90％RH（无冷凝状态）tus）tus) 大气压：860hPa〜1060hPa |
| 防水等级 | IPX4 |
| 电击保护 | I类，CF型 |
| 报警： | 闭塞，几乎完成，完成，待机（无操作），门打开，电池电量不足，电池耗尽等 |
| 功能 | 电源指示灯，输液量显示，流量显示，输液量显示等。 |
特殊功能
1.保持静脉打开（KVO）：完成预定的输注体积后，为防止血栓形成，继续输注，预设最低速率为0.1-5ml / h（设定）。
2.电源开关功能：当交流电源关闭时，它将自动切换到内部电池电源并同时提示。当交流开关时，它会自动转换回交流电源。
3.重复报警功能：操作员按下“”键后，如果引起报警的原因未经处理约2分钟，报警器再次发出声音，提醒操作人员解决问题。
4.数据存储功能：保存音量，品牌和遮挡压力级别的最后一个设置，以备下次使用。最长的记忆时间是5年。
5.灯光：为方便起见，在夜间或黑暗中安装或拆卸IV线时，门打开后灯会自动开启。灯是LED光源（白色）。
6.电池保护报警：为了保护电池并确保输液安全，当电池的电量从接近耗尽变为几乎耗尽时，有不同程度的声光提示。
7.移动：当用户尝试取出或取出注射器时，给出移动报警。
8.高流量安全确认：为了保证输液安全，当流量大于300ml / h（或等效）时，装置将提示用户再次确认，确认前不进行输液。
9.气泡报警：进入人体的气泡不断增多，可形成空气栓塞，危及生命。所以当气泡长度约为3mm（10.6ul）或累积气泡长度约为3mm（10.6ul）时，会触发声光报警。
10.滴液传感器斜率：在d / min模式下，当出现管道斜坡，液体溢出和误放/移动传感器等问题时，会发出报警。
| Model NO. | AIO-10B |
| Medical Device Regulatory Type | Type 2 |
| Certificate | CE ISO |
| Syringe Size | 5/6ml, 10/12ml, 20/25ml, 30/35ml,50/60ml |
| Infusion Range | 0.1ml~9999.9ml, Original Value Is 0.1ml |
| Kvo | 0.1~5ml/H |
| Electric Shock Protection | Class I, Type CF |
| Specification | CE ISO |
| HS Code | 8413190000 |
| Medical Devices Reg./Record No. | Hsyjxz20132540393 |
| Power Supply | AC 100V~AC 242V,50/60Hz |
| Built-in Batteries | DC 12V 1800mAh, Ni-MH, Rechargeable |
| Flow Selection | 0.1ml/H~1600ml/H, Original Value Is 0.1ml/H |
| Flow Rate Precision | ±3%plusmn;3%lusmn;3% |
| Waterproof Level | Ipx4 |
| Trademark | healicom |
| Origin | Jiangsu, China |
Basic Parameter
| Item Model | AIO-10B | AIO-10C |
| Dimensions(mm) | 354(L)×132(W)×199(H)×199(H)199(H)×199(H) | 354(L)×132(W)×268(H)×268(H)268(H)×268(H) |
| Weight | 2.7kg | 3.6kg |
| Battery Continuous Use Time | About 6 hours (fully charged new battery running with rate 5ml/h) | About 5 hours (fully charged new battery running with rate 5ml/h) |
| Rated Consumption | ≤25 VA5 VA5 VA | ≤35 VA5 VA5 VA |
Specification
| Power Supply | AC 100V~AC 242V,50/60HZ |
| Built-in Batteries | DC 12V 1800mAh, Ni-MH, rechargeable |
| Infusion Flow Selection | 0.1ml/h~1200ml/h (1-150d/min), original value is 0.1ml/h (1d/min) |
| Syringe Flow Selection | 0.1ml/h~1600ml/h, original value is 0.1ml/h |
| Syringe Size | 5/6ml, 10/12ml, 20/25ml, 30/35ml,50/60ml |
| Bolus Rate | Syringe 50ml:1600ml/h Syringe 30ml:900 ml/h Syringe 20ml:600 ml/h Syringe 10ml:400 ml/h Syringe 5ml: 200ml/h |
| Infusion Range | 0.1ml~9999.9ml, original value is 0.1ml |
| Infusion Precision | volume mode ±5%, drop mode ±2dmode ±2dusmn;2dmode ±2d |
| Syringe Flow Rate Precision | ±3%lusmn;3%lusmn;3% |
| KVO | 0.1~5ml/h |
| Occlusion Pressure | High:110kPa±20kPa (825mmHg±150 mmHg)lusmn;150 mmHg)lusmn;150 mmHg) Middle:80kPa±30kPa(600mmHg±225mmHg)plusmn;225mmHg)plusmn;225mmHg) Low:60kPa±20kPa(450mmHg±150 mmHg)lusmn;150 mmHg)lusmn;150 mmHg) The biggest output pressure:< 975mmHg(130kPa)kPa) |
| Use Environment | Temperature: 5ºC~43ºCC~43ºCrdm;CC~43ºC Relative Humidity:≤90%RH (Under without condensation status)tus)tus) Atmospheric Pressure:860hPa~1060hPa |
| Storage Environment | Temperature:-20ºC~+55ºC~+55ºCrdm;C~+55ºC Relative Humidity:≤90%RH (Under without condensation status)tus)tus) Atmospheric Pressure:860hPa~1060hPa |
| Waterproof Level | IPX4 |
| Electric Shock Protection | Class I, Type CF |
| Alarm: | occlusion, nearly finish, finish, standby (no operation), door open, low battery, battery exhausted etc. |
| Function | power indicator, transfusion amount display, flow rate display, infused volume display etc. |
Special Function
1. Keep-Vein-Open (KVO): After finishing predetermined infusion volume, to prevent the formation of thrombus, continue infusion with preset minimum rate 0.1-5ml/h(setted).
2. Power Supply Switching Function: When the AC power supply is off, it will automatically switch to internal battery power supply and prompt at the same time. When AC is switched on, it is automatically converted back to AC supply.
3. Repeat Alarm Function: After the operator presses the '' key, if the reason causing the alarm has be untreated for about 2 minutes, the alarm will sound again to alert the operator to solve the problem.the problem.
4. Data Memory Function: Save the last setting of sound volume level, brand and occlusion pressure level, to prepare for the next use. The longest memory time is 5 years.
5. Light: For convenience, when installing or removing IV line at night or in darkness, light will automatically turn on after the door is open. The light is an LED light source (white).
6. Battery Protection Alarm: In order to protect the battery and ensure infusion safety, there are different levels of acousto-optic prompts when the electric quantity of the battery is changing from close to depletion to almost depleted.
7.Move: When user tries to remove or take away the syringe, give move alarm.
8. High Flow Safety Confirm: In order to ensure infusion safety, when the flow rate is greater than 300ml/h (or equivalent), the device will prompt user to confirm again, and will not carry out infusion before confirmation.
9. Bubble Alarm: A continuously large number of bubbles going into the human body can form the air embolus, and it is life-threatening. So when bubble length is about 3mm (10.6ul) or accumulated bubble length is about 3mm (10.6ul) is detected, will trigger acoustic-optic alarm.
10. Drip Sensor Slope: In d/min mode, when there are problems such as tube slope, liquid overflow and misplaced/moved sensor, there will be an alarm.
