Features
A. Rapid heating, and energized for 5 minutes
Two. Automatic thermostat design, for EVA pine December synthetic rubber, Synthetic rubber strips and a variety of low melting point of polyethylene plastic resin strip, adjust the desired temperature, the proper control of the melt viscosity.
3. Quick to heat up. Which means that heat. Continuous work on the production line will not reduce the temperature.
4. Energy efficient thermostats work; melt glue gun; power consumption reduced by 50%

5 Melt glue gun is the use of integrated control the heating element, long life and durable.
6. Barrel design is relatively light. Long-term use will not fatigue.
7 one-hand operation, very precise control of the output of the melt.
8. Improve the working environment, reduce labor intensity and improve working efficiency.
Security
A. Anti-overheating design near the heating element; temperature fuse; to prevent a high degree of overheating
Two. Double insulation. Electric strength of up to 3750V insulation resistance greater than 100M Europe
3. Barrel is compact and sturdy. Heat shock plastic manufacturing
4. Does not contain any organic solvents. Not cause environmental pollution
The main purpose
EVA rosin synthetic rubber strips, synthetic rubber strips of polyethylene plastic resin and a variety of low-melting-point strip
Paste card cartons, corrugated boxes and other
Solid wood
Solid plastic and metal
Solid glass and ceramic products
Solid textiles and shockproof packaging material
Packaging system for port
Specification


Model
SD-860
SD-866


Power
220V-50HZ
220V 50HZ 110W


Temperature
High temperature
110-220 / ℃


Strip category
Softening point 40-80 ℃

Melting temperature of 100-220 ℃

(The above data are for reference only)
Softening point 40-80 ℃

Melting temperature of 100-220 ℃

(The above data are for reference only)




Recommended temperature


Tape types
Set temperature

EVA white strips
160 ℃

EVA rosin syntheic bar
130 ℃

Synthetic rubber strips of polyethylene plastic resin
100 ℃



Use

A. Will tape sent by the end of the melt glue gun directly into the nozzle
Two. Pull the trigger you can precisely control the output of the melt
3. Warm up for five minutes can be used normally after power


Note
The use of a melt glue gun should be checked before voltage are consistent with

2 should be selected with a marked temperature melt adhesive tape, adjust the temperature of the melt glue gun and melt tape temperature before the corresponding

3 recommendations melting strips diameter of 10.8 to 11.5 mm, other size melt adhesive tape, may be down caused by the reflux to avoid melting plastic strips used for a long storage

4 yellow tape has a strong suction temperature; attention kept under seal; should soon be opened; if the moisture absorption of the yellow tape; may lead to the failure of the melt glue gun

5 melt glue gun work; melt glue may cause the nozzle temperature of 100 ° C above; very hot; please do not let the human body with the mean close to

6 sol gun should be kept dry in a humid environment to avoid very high or very low temperature place melt glue gun

7 melt glue gun without any percussion, dismantle and installation of other electric parts parts

8 new melt gun for the first time, the heating of the heating element may be a slight smoke, which is a normal phenomenon disappear automatically after ten minutes.

The work of the 9-melt glue gun; adhesive thermal expansion of the nozzle there will be a small amount of glue out; this is a normal phenomenon

10 is too high melt temperature may cause the glue gun nozzle leakage glue; such as melt glue gun nozzle leakage of plastic; may be appropriate to adjust the temperature of the melt glue gun to avoid leakage of glue

11 melt glue gun to use to keep the muzzle downward or horizontal direction to avoid the muzzle up, causing the adhesive back in failure

12 melt glue gun at intervals over 10 minutes to re-use; the nozzle will appear adhesives stagnation flow; which is a normal phenomenon; quickly tap the trigger until the adhesive smooth outflow until

13 melt glue gun to suspend the work of more than 20 minutes; to cut off the power to prevent long power space heating; resulting in the glue gun to glue the back of accidents caused by

14 melt glue gun use should be based on formal release

Condition: Brand new

Size: 19cm X 16cm X 3cm

Weight: 0.33 Kg

Material: Heat resistant plastic

Colour: as picture

SKU: 901959-A01-14-06

Notice: Color of pictures may varies by different monitor setting. All pictures are real stock photos.

特 点
1. 快速升温, 通电5分钟即可使用
2. 自动恒温设计, 适用于EVA松腊合成胶条, 聚胶脂合成胶条及各种低熔点胶条, 调节所需要的温度, 能适当控制熔胶之粘度.
3. 快速升温. 即开即热. 在生产流水线上连续工作都不会减低温度.
4. 高效节能的恒温工作方式, 使熔胶枪的耗电量降低50%

5. 熔胶枪采用一体化控热元件, 寿命特长耐用.
6. 枪身设计比较轻盈. 长时间使用都不会疲劳.
7. 单手操作, 能够很精确的控制熔胶输出量.
8. 改善工作环境, 降低劳动强度, 提高工作效率.
安 全
1. 防过热设计; 在发热元件附近内有温度保险丝; 防止高度过热
2. 双重绝缘. 电气强度高达3750V, 绝缘电阻大于100M欧
3. 枪身紧凑坚固. 使用耐热防震塑料制造
4. 不含任何有机溶剂. 不会造成环境污染
主 要 用 途
EVA松脂合成胶条, 聚胶脂合成胶条及各种低熔点胶条
粘贴咭纸箱, 瓦楞纸箱等
稳固木材
稳固塑胶和金属
稳固玻璃及陶瓷制品
稳固纺织品及防震包装料
包装制口
规 格

型号
SD-860
SD-866


功率
220V-50HZ
220V 50HZ 110W


温度
高温型
110-220/ ℃


使用胶条类别
软化点40-80℃

熔融温度100-220℃

(以上数据, 仅供参考)
软化点40-80℃

熔融温度100-220℃

(以上数据, 仅供参考)

推荐使用温度

胶条种类
设定温度

EVA白胶条
160℃

EVA松脂合成胶条
130℃

聚胶脂合成胶条
100℃

使用方法

1. 将胶条由熔胶枪尾部直接插入送至喷嘴
2. 扣动扳机可以精确控制熔胶输出量
3. 通电后预热5分钟可以正常使用

注意事项
1熔胶枪使用前应检查电压是否相符

2应选取附有温度标示的熔胶条, 调节熔胶枪的温度与熔胶条的温度相应才可

3建议所使用的熔胶条的直径为10.8至11.5毫米, 如果使用其它尺寸的熔胶条, 可能倒致回流, 避免使用久储的熔胶胶条

4黄胶条具有很强的吸温性; 注意密封保存; 打开后应该很快使用; 如果用吸潮的黄胶条; 可能会导致熔胶枪的失灵

5熔胶枪工作时; 熔化的粘胶可能会导致喷嘴的温度达到100℃以上; 十分的热; 请不要让人体随意思靠近

6溶胶枪应保持干燥; 不就在潮湿的环境中使用; 避免在非常高温或非常低温的地方使用熔胶枪

7熔胶枪工作时不的任意敲击, 折除以及安装其它电热部分零件

8新熔枪首次使用时; 因电热元件供热而可能轻微发烟; 这是正常现象; 十分钟后就自动消失

9熔胶枪工作时; 由于粘胶剂受热膨胀的原因; 喷嘴会有小量的粘胶剂出来; 这是正常现象

10过高的熔胶温度可能会引致胶枪的喷嘴漏胶; 如发现熔胶枪喷嘴漏胶时; 可适当调节熔胶枪温度; 可避免漏胶

11熔胶枪使用就保持枪嘴向下或水平方向; 避免枪嘴向上; 造成粘胶剂倒流出现故障

12熔胶枪在间隔时间超过10分钟重新使用时; 喷嘴会出现粘胶剂滞流的情况; 这是正常现象; 只要快速轻按扳机; 直至粘胶剂顺利流出为止

13熔胶枪暂停工作超过20分钟时; 要切断电源; 防止长时间通电空加热状态; 造成胶枪粘胶剂出现回流引致意外

14熔胶枪使用时应该按正规放

成色: 全新

尺寸: 19厘米X 16厘米X 3厘米

重量: 0.33千克

材料: 耐热塑料

颜色: 如图片

SKU: 901959-A01-14-06

注意: 因显示器设置不同可能导致色差, 但所有图片均来自实物拍摄, 请放心选购.