2 E1 Timeslot ADD\DROP to Ethernet converter

2 E1 Timeslot ADD\DROP to Ethernet converter

2 E1时隙分/插以太网转换器

议价

加入意向

描述

在E1时隙上/下转以太网转换器可以提取部分时隙从E1信道来实现的RS232 / RS422 / RS485串口数据或以太​​网数据1/2/4/8通道（S）的多路传输，设备 可以通过级联连接构造链网络，与中央服务器可以收集串行端口或数据中的E1时隙以太网数据，并经由IP模式上传。 它可广泛应用在电力环境监测与控制，电力监控，移动基本站的监测和控制，信令7号的监测和控制，移动充电网络和其他类似的数据收集系统和远程互连系统。

人物

  • 基于自主知识产权的集成电路;
  • 10M / 100M以太网，全/半双工自动适应，支持VLAN。
  • 以太网支持Auto-MDIX（跨越和直通自我适应）
  • 支持3种环回功能，下行链路E1自环（ANA），上行E1环回（DIG），命令环回远程五，35和ETH接口（REM）;
  • 有伪随机码检测的功能; 这使安装了极大的方便; dBDugging和设备维修; 并且可被用作一条E1 miscode测试仪;
  • 供电方面，AC220V，DC-48V，DC24V等模式选择;
  • 当DC-48V / DC24V，电源阴极和阳极可以在不影响设备工作的连接方式;

参数

E1接口
标准：E1接口与G. 703标准兼容。
价格：N * 64 kbps的（N = 1-32）
编码：HDB3
阻抗：75Ω（非平衡）
连接器：BNC（75Ω）
抖动性能：根据G. 742和G. 823
时钟模式：电路时钟
10 / 100BASE-T以太网端口
价格：10M / 100M，全/半双工自动适应。
协议：支持IEEE 802.3，IEEE 802.1磷，802.1Q（VLAN）
MAC地址表：4096的MAC地址。
以太网缓冲区：64Mbits SDRAM
物理接口：RJ45，支持AUTO-MDIX（交叉和直连网自我适应）
工作条件：
输入电压：AC22​​0V; AC 110V; DC-48V; DC + 24V
功耗：≤5W
工作温度：0〜50degree
储存温度：-40〜+ 70度
相对湿度：95％
应用：
应用1：在PIONT使用的FE1转换器FE1 +以太网点
应用2：使用具有收敛服务器，几个节点的以太网数据汇聚到一个以太网

Description

The E1 timeslots add/ drop to ethernet converter can extract partial time-slots from E1 channel to implement multiplexing transmission of 1/2/4/8 channel (s) of RS232/ RS422/ RS485 serial port data or Ethernet data, and the equipment can construct chain network by cascade connection, and the central server can collect serial port data or Ethernet data of E1 time-slots, and upload it via IP mode. It can be extensively used in the power environment monitoring and control, power monitoring and control, mobile basic station monitoring and control, Signaling Number 7 monitoring and control, mobile charging network and other similar data gathering system and remote interconnected system.

Characters

  • Based on self-copyright IC;
  • 10M/ 100M Ethernet, full/ half duplex self adapt, support VLAN.
  • Ethernet support AUTO-MDIX (cross over and straight through self adapt)
  • Support 3 kind loop functions: down-link E1 self-loop (ANA) , up-link E1 loop back (DIG) , command loop back of remote V. 35 and ETH interface (REM) ;
  • Have the function of pseudo-random code testing; which brings great convenience for installation; dBDugging and maintenance of equipment; and can be used as an E1 miscode tester;
  • Power supply, AC220V, DC-48V, DC24V etc. modes for option;
  • When in mode of DC-48V/ DC24V, connection of power supply cathode and anode can not affect device working;

Parameters

E1 interface
Standard: E1 interface compatible with G. 703 standard.
Rate: n*64 kbps ( n= 1-32)
Coding: HDB3
Impedance: 75Ω (unbalance)
Connector: BNC (75Ω)
Jitter Performance: According to G. 742 and G. 823
Clock mode: circuitry clock
10/100Base-T Ethernet port
Rate: 10M/ 100M, full/ half duplex self adapt.
Protocol: support IEEE 802.3, IEEE 802.1 P, 802.1Q (VLAN)
MAC address table: 4096 MAC addresses.
Ethernet buffer: 64Mbits SDRAM
Physical interface: RJ45, support AUTO-MDIX (cross-over and straight- through self adapt)
Working condition:
Input voltage: AC220V; AC 110V; DC-48V; DC+24V
Power consumption: ≤5W
Operating temperature: 0~ 50degree
Storing temperature: -40 ~ +70 degree
Relative humidity: 95 %
Application:
Application1: the piont to point using, the FE1 converter to FE1+Ethernet
Application2: Used with convergence server, several node's ethernet data are converged to one ethernet