16E1 to Optical Ethernet converter | optical ethernet over 16E1

16E1 to Optical Ethernet converter | optical ethernet over 16E1

16E1到光纤以太网转换器| 光以太网16E1

议价

加入意向

产品功能： BD-16E1-OETH转换器采用反向复用技术与粘接多路E1通道，从而实现1-16路E1和以太网接口之间的转换传输的10 / 100BaseT数据。它可以发射信号点至点从E1通道RJ45接口，实现E1通道和以太网之间的连接。依据从一般长途桥不同，此转换器支持1至16个信道的E1的灵活的配置和能够检测E1通道的数目和选择可利用信道。在此期间，传输延迟时间的某些差异E1通道之间允许的。当10 / 100Mbps自适应全/半双工模式下使用，该设备可与以太网交换机或集线器（集成电路机）连接通过充分利用大量的E1通道的当前电信网络扩展以太网的传输距离和应用范围。它是用于连接以太网宽带的最佳解决方案。该产品可在很多领域得到应用，如LAN的连接和端局，视频点播（VOD），远程监控和交换机的E1接口。

特征：

  • 实现了1到16个E1信道以太网数据的透明传输。
  • 以太网支持10M / 100M，全双工/半双工自动negociation，支持VLAN。
  • 以太网端口支持AUTO-MDIX（跨越和直通自动适应）。
  • 设置CRC告警限制自动隔离线，低传输质量（被削减的单定向）;当在2M分支一个方向的误码率超过了限制，该方向被切断，而另一个方向将不会受到影响，即以太网的两个发射方向可以是不对称的。
  • 允许16路E1高达10ms的传输延迟。当延迟超过允许的极限范围内，它可以自动停止发送数据。
  • 有2环回功能：E1本地环，E1远端环。
  • 支持本地地址过滤功能动态以太网MAC地址（4096）。
  • E1接口符合ITU-T G. 703，G 704和G 823不支持的信号时隙兼容。
  • E1接口已经内部时钟恢复电路和HDB3编码/解码电路。
  • 支持E1信道的热插拔，并自动检测有效的E1信道数据传输不会被削减。
  • 支持自定义配置1到16个E1信道，自动检测E1信道的数量，并选择重置时可用的E1。
  • 支持从本地系统重置远程系统。
  • 支持SNMP网管
  • 有以太网监控自动复位功能。

    参数规格
    E1接口
    标准：E1接口与G. 703标准兼容。
    价格：为2.048Mbit /są50ppm
    编码：HDB3
    阻抗：75欧姆（不平衡）或120欧姆（平衡）
    连接器：BNC（75欧姆）或RJ45（120欧姆）
    抖动性能：根据G. 742和G. 823
    10 / 100BASE-T
    速度：10M / 100M，全双工/半双工自动适应。
    协议：支持IEEE 802.3，IEEE 802.1Q（VLAN）
    MAC地址表：4096的MAC地址。
    以太网缓冲区：64Mbits SDRAM
    物理接口：RJ45，支持AUTO-MDIX（跨越和直通自动适应）
    尺寸
    19英寸机架安装式：433毫米（L）38毫米（W）44毫米（高）
    操作环境
    电压：DC-48V，输入范围：DC-36V〜DC-72V
    功耗：（= 5瓦
    工作温度：0℃〜50℃
    储存温度：-40℃〜+ 70℃
    湿度：95％
    无腐蚀性溶剂，无粉尘，无强磁场干扰。

    应用：

    • Product function: BD-16E1-OETH converter uses reverse multiplexing technology to transmit 10/100BaseT data with bonding multi E1 channels, thus realizing conversion between 1-16 E1 channels and Ethernet interface. It can transmit signals point-to-point from E1 channel to RJ45 interface to realize connection between E1 channel and Ethernet. Being different from general long-distance bridge, this converter supports flexible configuration of 1 to 16 channels E1 and can detect the number of E1 channel and choose available channel. In the meantime, certain difference of transmitting delay is allowed among E1 channels. When used in 10/100Mbps half/ full duplex mode, this equipment can be connected with Ethernet switch or hub (integrated circuit machine) to expand transmitting distance and application scope of Ethernet by making full use of large number of E1 channels in current telecommunication network. It is an excellent solution for connecting Ethernet broadband. This product can be applied in many fields such as connection of LAN and end offices, video ordering (VOD) , remote monitor and E1 interface of switches.

    Features:

  • Realizes transparent transmission of Ethernet data in 1 to 16 E1 channels.
  • Ethernet supports 10M/ 100M, full/ half duplex auto-negociation, supports VLAN.
  • Ethernet port supports AUTO-MDIX (cross over and straight through auto-adapt) .
  • Setting CRC alarm limitation to auto isolate lines with low transmitting quality (being cut single-directionally) ; when error code rate of one direction in 2M branch exceeds the limitation, this direction is cut and the other direction will not be affected, namely the two transmitting directions of Ethernet can be unsymmetrical.
  • Allow 16 E1 channels up to 10ms transmission delay. When the delay exceeds allowed limit range, it can stop transmitting data automatically.
  • Has 2 loop back functions: E1 local loop, E1 remote loop.
  • Supports Dynamic Ethernet MAC address (4096) with local address filter function.
  • E1 interface compatible with ITU-T G. 703, G. 704, and G. 823. not supporting signal timeslot.
  • E1 interface has internal clock recover circuit and HDB3 code/ decode circuit.
  • Supports E1 channel hot plug, and auto detect effective E1 channels data transmission will not be cut.
  • Supports 1 to 16 E1 channels customized configuration, auto detect the number of E1 channels and select the available E1 when resetting.
  • Supports resetting remote system from local system.
  • Support SNMP network management
  • Having Ethernet monitor auto reset function.

    Parameter and specifications
    E1 interface
    Standard: E1 interface compatible with G. 703 standard.
    Rate: 2.048Mbit/ są50ppm
    Coding: HDB3
    Impedance: 75ohm ( unbalance) or 120ohm (balance)
    Connector: BNC (75ohm) or RJ45 (120ohm)
    Jitter Performance: According to G. 742 and G. 823
    10/100Base-T
    Rate: 10M/ 100M, full/ half duplex auto-adapt.
    Protocol: Support IEEE 802.3, IEEE 802.1Q (VLAN)
    MAC address table: 4096 MAC addresses.
    Ethernet buffer: 64Mbits SDRAM
    Physical interface: RJ45, support AUTO-MDIX (cross over and straight through auto-adapt)
    Dimension
    19inch rackmount type: 433 mm (L) �38mm (W) �44 mm (H)
    Operating environment
    Voltage: DC-48V , input range: DC-36V~DC-72V
    Power Consumption: (=5 Watts
    Working temperature: 0C~50C
    Storage temperature: -40C~+70C
    Humidity: 95%
    No causticity and solvent, dust free, and no strong magnetic interference.

    Application: