8E1 to Optical Ethernet Converter
8E1光以太网转换器
议价
加入意向功能
8E1-100Base-FX串行接口转换器用于回多路复用技术，传输10M / 100M以太数据通过多E1通道。 实现转换的1至8路E1和以太网接口。 它可以传输E1通道的信号，RJ45接口点对点，实现E1通道和以太网的连接。 它不同于正常的桥接器，支持1至8路E1的自定义配置，自动检测E1信道的数量和使用可用的E1，允许不同的E1通道之间的一些限制传输延迟。 单个线速度1968Kbits /秒，8个信道可高达15744Kbits /秒。 它可以与以太网交换机或集线器连接时，在10 / 100Mbps自适应全/半双工模式下，利用大规模的E1资源的电信网络耗费以太网的传输距离和应用领域，是宽带交换机在以太网的一个合适的解决方案。 它可以在如连接局域网，连接端局，视频点播，远程监控，交换机E1接口等领域中使用
特征
- 实现以太数据通过1的透明传输8路E1线路
- 提供 10 / 100BASE-TX和100BASE-FX接口 符合协议
- 标准IEEE 802.3，提供2个电子化的以太网端口和一个光纤以太网接口
- 无论是支持全双工或半双工的工作模式。
- 能够透明地传输超长帧（最大1916字节）的IEEE 802.1Q协议规定，支持VLAN帧的透明传输。
- 提供了一个内置动态以太网MAC地址列表（1024个地址）与过滤功能的本地数据帧。
- 128MBits大容量高速缓冲存储器和一个内置SDRAM控制器，以适应各种业务的要求。
- E1接口符合ITU-T G. 703，G 704和G 823，不适用于信令时隙。
- E1支持75|¸/不平衡阻抗或120|¸/平衡订单
- 允许一个时钟漂移到512UI在传输系统，具有显著增强的可靠性。
- 为1至7 E线处提供可用性检测和自动故障排除。
- 支持E1接口环回功能和以太网环回功能。
- 自包含的线路告警指示和输出。
- 可选的电源，如 G。 AC220V或DC-48V; 可选安装型，E。 G。 桌面或机架安装。
- 功耗：（10瓦
|
|  |  |
|
电源 工作电压范围宽，良好的 防干扰和隔离，工作稳定 选择我直流-48V，范围DC-36V〜DC-72C 选项II AC220V，AC165V范围〜AC240V 功耗：（= 10瓦 环境条件 工作温度：0℃〜+ 50℃ 储存温度：-20℃〜+ 70℃ 相对温度：95％（未冷凝） |
| 尺寸 440毫米（L）X202mm（宽）X43.5mm（H）的 |
| |
应用：
Functions
8E1-100Base-FX serial interface converter used back multiplexing technology, transfer 10M/ 100M Ethernet data by using multi E1 channels. Realize convert between 1 to 8 E1 channels and Ethernet interface. It can transmit signal of E1 channel to RJ45 interface point to point, realize the connection of E1 channel and Ethernet. It different from normal bridge , supporting 1 to 8 E1 channels customized configuration, auto detecting the number of E1 channels and use the available E1, allow some limiting transfer delay between different E1 channels. Single line speed is 1968Kbits/ s, 8 channels can up to 15744Kbits/ s. it can connect with Ethernet switch or hub when in 10/100Mbps full/ half duplex mode, make use of mass E1 resource in telecommunication networks to expend the transfer distance and application field of Ethernet, is a suitable solution for broadband switch in of Ethernet. It can used in fields such as connecting LANs, connecting end offices, VOD, remote monitor, E1 interface of switches, etc.
Features
- Realizing the transparent transmission of Ethernet data via 1 to 8 E1 lines
- Providing 10/100Base-Tx&100Base-Fx interface in compliance with the protocol
- standard IEEE 802.3, providing 2 electronical Ethernet ports and one optical Ethernet port
- supporting the working mode of either full duplex or half-duplex.
- Able to transparently transmit the ultra-long frames (up to 1916 bytes) as defined in IEEE 802.1Q, supporting transparent transmission of VLAN frames.
- Providing an in-built dynamic Ethernet MAC address list (1024 addresses) with filtering function for local data frames.
- 128MBits large capacity cache memory and an in-built SDRAM controller, to adapt to various service requirements.
- E1 interface in compliance with ITU-T G. 703, G. 704 and G. 823, not applicable for signaling time slot.
- E1 Support 75¦¸/ unbalance impedance or 120¦¸/ balance for order
- Allowing a clock drift up to 512UI in the transmission system, with significantly enhanced reliability.
- Providing availability detection and automatic troubleshooting for 1 to 8 E lines.
- Supporting E1 interface loop-back function and Ethernet loop-back function.
- Self-contained line alarm indication and output.
- Optional power supply, e. g. AC220V or DC-48V; optional mounting type, e. g. desktop or rack mounted.
- Power consumption: (10 W
|
| | |
|
Power supply working voltage range wide, good anti-disturb and Isolation, work stable option I DC-48V, range DC-36V~DC-72C option II AC220V, range AC165V~AC240V Power Consumption: (=10 Watts environment condition Operating temperature: 0C~+50 C Storage temperature: -20 C~+70 C Relative temperature: 95% (uncondensed) |
| Dimension 440mm (L) X202mm (W) X43.5mm (H) |
| |
Application:
