Radio Receiver/Transmitter, 220 to 2 Zone which Control AC-powered Garden Lights
无线电接收器/发射器，220到2区控制交流供电的花园灯
议价
加入意向- 使用说明书
- 包含在包中已经编程和准备使用
- 区域1和2可以双稳态或定时模式独立操作
- 设置操作模式：
- 区域1：
- 双稳态：移除端子1和2上的跳线
- 定时：将跳线插入端子1和2
- 区域2：
- 双稳态：卸下端子2和3上的跳线
- 定时：在端子2和3上插入跳线
- 区域1：
- 无线控制获取：
- 区域1：
- 按下控制单元上的P1键编程退出Z1，LED将保持点亮
- 按住要在无线电控制单元上获取的键，然后按下
- 主控制单元开始闪烁，松开键
- 区域2：
- 按下控制单元上的P1键两次编程exitZ2，LED将保持开启
- 按住要在无线控制器上获取的键，直到LED开始
- 闪光，松开键
- 区域1：
- 设置工作时间：（存在时间）
- 仅当使用定时模式时
- 区域1：
- 按主控制单元上的键P2一次，设置退出Z1的工作时间，LED将亮
- 在exitZ1上设置，然后再次按P2键
- LED会闪烁三次确认
- 区域2：
- 按主控制单元上的键P2一次，设置退出Z2的工作时间，LED将亮
- 来吧
- 等待一段时间等于在exitZ2上设置的工作时间，然后按键
- P2
- LED会闪烁三次确认
- 删除无线电控制代码：
- 删除个别代码：
- 按住主控制器上的P1键5秒钟（松开键），LED将亮起
- 保持
- 按下无线电控制器上的键，直到LED开始
- 闪
- 删除所有代码：
- 按住主控制器上的P1键10秒钟，LED将亮起
- 打开，然后松开键
- LED将发出3次闪烁以确认删除所有
- 代码
- 删除个别代码：
- Instruction manual
- Included in the pack are already programmed and ready touse
- Zones 1 and 2 can operate independently in bistable or timedmode
- Setting the mode of operation:
- Zone 1:
- Bistable: remove the jumper on terminals1and 2
- Timed: insert the jumper on terminals1and 2
- Zone 2:
- Bistable: remove the jumper on terminals 2 and 3
- Timed: insert the jumper on terminals 2 and 3
- Zone 1:
- Radio control acquisition:
- Zone 1:
- Press key P1 on the control unit once to program exit Z1, theLED will remain on
- Press and hold the key to be acquired on the radio control unituntil the LED on the
- main control unit starts to flash ,release the key
- Zone 2:
- Press key P1 on the control unit twice to program exitZ2, theLED will remain on
- Press and hold the key to be acquired on the radio control unituntil the LED starts to
- flash, release the key
- Zone 1:
- Setting the work time: (time the existion)
- Only if timed mode is used
- Zone 1:
- Press key P2 on the main control unit once to set the work timefor exit Z1, the LED will
- set on exitZ1, after which press key P2 again
- LED will flash three times to confirm
- Zone 2:
- Press key P2 on the main control unit once to set the work timefor exit Z2, the LED will
- come on
- Wait a length of time equal to the work time to be set on exitZ2, after which press key
- P2 again
- LED will flash three times to confirm
- Deleting the radio control codes:
- Deleting an individual code:
- Press and hold key P1 on the main control unit for 5 seconds(release the key), the LED will
- remain on
- Press the key on the radio control unit to be cancelled untilthe LED begins to
- flash
- Deleting all codes:
- Press and hold key P1 on the main control unit for 10 seconds,the LED will come
- on, then release the key
- LED will emit 3 flashes to confirm the deletion of all the
- codes
- Deleting an individual code:
