1x2 MagLight Optical Switch
1×2磁光开关
议价
加入意向1x2 MagLight Optical Switch Specification
1x2 MagLight Optical Switch
Applications:
Optical switching
High speed protection
System monitoring, Test & measurement
Fiber-optics sensing system
Features:
No moving parts, best durability
Ultra fast switching speed
Extremely stable latching mode
Low power consumption
Easy to route -all fibers on same side
Exceptional reliability and stability
Fiberer-1x2 MagLight Optical Switch is an all solid-state devcie without any moving parts. The switching of the optical light is realized by utilizing Faraday Effect. This is achieved using a patent protected non-mechanical configuration with solid-state all-crystal design which eliminates the need for mechanical movement. The microsecond fiber optic switch is designed to meet the most demanding switching requirements of reliability, durability, response, and continuous high frequency switching.
Specifications:
| Item | Unit | Parameters | Notes | |
| Unidirectional | Bidirectional | |||
| Wavelength Range | nm | 1525~1565 | Other band optional | |
| Insertion Loss | dB | 0.8 (Typ.) ; 1.1 (Max.) | 1.0 (Typ.) ; 1.3 (Max.) | Add 0.4dB for high-power version |
| PDL | dB | 0.1 (Typ.) ; 0.2 (Max.) | | |
| Return Loss | dB | 40 | 30 | |
| Cross-talk | dB | 40 | 35 | Typical ) 50dB |
| PMD | ps | 0.2 | | |
| Repeatability | dB | +/ - 0.01 | | |
| Durability | cycles | ) 30 Billions | | |
| Switching Speed | 渭s | Regular (200~400) ; Ultra-fast (10~30) | Other speed optional | |
| Storage Temperature | 0C | -40~85 | | |
| Operating Temperature | 0C | -5~70 | | |
| Maximum Optical Power | mW | 500 (for high-power version: 5W for CW laser. 700W of peak power for ns-scale pulsed laser) | | |
| Dimension ( L � W�H ) | mm | 39�9.0�9.5 | | |
All the specifications are based on the devices without connectors, and guaranteed over wavelength, polarization and temperature.
**. Specifications are subject to change without notice.
Dimensions Drawing (mm) :
Electrical Specifications:
| Parameters | Specifications | U nit | |
| Switching Speed | 200~400 | 10~30 | 渭s |
| Switching Voltage (VCC) | 4.5~5.5 | 6.5~7.5 | V |
| Switching Current | ( 100 | ( 350 | mA |
| Driving Mode | Voltage or Pulse Driving | Pulse Driving | NA |
| Pulse Width (typical) | 1000 | 15 | 渭s |
| Claim Frequency | (800 | ( 3000 | Hz |
Notes:
l Fiberer provides optional switch driving board at additional charge;
l It is recommended to use Fiberer switch driving board for the Ultra-fast switch;
l To avoid damaging the Ultra-fast switch, Fiberer recommends to set the current limit below 800mA when the power supply voltage is set at 6.5V~7.5V.
Pin control signal corresponding to switching status table:
| Pin1 | Pin2 | The Optical Output Port |
| 1 (Voltage = VCC) | 0 (Voltage = GND) | ON |
| 0 (Voltage = GND) | 1 (Voltage = VCC) | OFF |
Ordering Information:
| A | B | C | D | E | F | G | H |
| Working Mode | Switch Speed | Operating Wavelength | Power Handing | Fiber type | Fiber diameter | Fiber Length | Connector |
| R.Regular (Unidirectional) B.Bidirectional | 1.200~400渭s 2.10~30渭s 3. Others | 1. C band 1525~1565nm 2. L band 1565~1615nm 3. C & L band 4. Others | 0. Standard 1. High Power | 5: 50/125 6: 62.5/125 9: 9/125 X: Others | 25: 250um 90: 900um; 20: 2.0mm X: Others | 05: 0.5m 10: 1.0m 15: 1.5m X: Others | OO: None FP: FC/ PC FA: FC/ APC SP: SC/ PC SA: SC/ APC SP: ST/ PC SA: ST/ APC LP: LC/ PC LA: LC/ APC X: Others |
Note:
Welcome to contact our engineers to know more info about the specification.
