安装简单，操作简单！

它是专为司机谁是累翻键启动的智能设备。

安装后，只需按动按钮时要启动或停止。

HT-002是一键启动按钮系统，其目的是与原始远程工作，从而使系统能够布防/撤防当驱动程序锁定/解锁他们的汽车。 因此，HT-002不具有PKE系统。

关于该系统的附件

HT-002包括三个部分：主机，按钮和线束。

主线束将被连接到您的汽车（+ 12V，ACC，ON，START）点火导线。

该8P线束包括3感电线，主要单位可以知道，如果你是锁定/受这些电线解锁你的车。 这些导线将连接到中心锁电机和转向灯电线，它们都应该是正的。

该按钮将被安装在汽车上，随时随地可以推得舒服，但我们建议您修复它到上述的钥匙孔。

如何使用它？

启动你的车： 踩脚制动器，然后按下按钮，如果你不想踩刹车，只需按下并保持了一段时间。

停止你的车： 作为同为起始。

按下按钮没有刹车，该系统将改变状态如下：

OFF-ACC-ON-OFF

布防anddisarming

1，布防： 该系统将手臂当驾驶员锁住由原来的遥控车辆。 如果您忘记了锁，不用担心，该系统可以武装自己在几分钟的时间。 （注：如果汽车电源没有关闭时，系统不能胳膊）。

2，撤防： 当驾驶员进行解锁原装遥控车辆，系统会解除武装。

因此，盗贼无法启动，即使他们强行打开门上车。

自武装

这是系统可以武装自己，请确保您已按你原来的遥控器上的开锁按钮。

由于自我武装，如果您忘记了LOCKING你的车，当你离开的时候，系统会自动布防，以防止你的carfrom窃取。

远程启动

THISIS一个惊人的功能，但并不是所有的汽车支持此功能，以售后市场汽车防盗系统，特别是汽车。

操作： 只需按下遥控作为一个特定的顺序对原解锁和LOCK按钮。

优点：

1.最重要的是我们是谁使用IC，适用于键式启动的唯一制造商。

我们知道，按钮启动系统提供电源车盯着节，特别是为IG1和IG2。 如果电力供应IG1和IG2的不稳定，发动机不能正常工作，这是有害的和危险的。 这就是为什么我们不使用继电器或FAMOS输出电力的车线，尽管巨大的成本差异。

2.该系统几乎消耗没有电时它武装，这意味着它不会增加多少你的车electricityconsumption的。

安装 - 如何面对这个转向锁和RFID防盗？

1. 方向盘锁： 最简单的方式是复制机械钥匙，将其插入钥匙孔并转动到ON位置，以保持转向轮解锁，然后切外侧部，最后，将其粘贴上面的按钮。

2. 原始RFID防盗： 取出RFID芯片从原来的遥控器和粘贴的位置靠近锁芯。 （不要担心你的遥控器，它是独立于大多数的遥控器如果RFID芯片焊接在遥控电路板，别把它。）

Simple installation and simple operation!

It is a smart device designed for drivers who are tired of turning key to start.

After installing it, just push the button when you want to start or stop.

HT-002 is a Push Start Button system, which is designed to work with the original remote, so that the system can arm/ disarm when drivers lock/ unlock their cars. So, HT-002 doesn't have PKE system.

About the accessories of the system

HT-002 includes three parts: main unit, button and harnesses.

The main harness will be connected to the ignition wires of your car (+12V, ACC, ON, START) .

The 8P harness includes 3 Sense wires, the main unit can know if you are locking/ unlocking your car by these wires. These wires will be connected to the central lock motor and turning light wires, they all should be positive.

The button will be installed in the car, anywhere you can push comfortably, but we recommend you fix it onto the above of keyhole.

How to use it?

Start your car: step on the footbrake, and then push the button, if you don't want to step the brake, just push and hold it for a while.

Stop your car: as same as starting.

Pushing the button without braking, the system will change status as below:

OFF-ACC-ON-OFF

Arming anddisarming

1. Arming: the system will arm when the driver locks the vehicle by original remote. If you have forgotten locking, don't worry, the system can arm itself in several minutes. (Note: if the car power hasn't been turned off, the system can't arm) .

2. Disarming: the system will disarm when the driver unlocks the vehicle by original remote.

So, thieves can't start the car even if they forced the door open.

Self-arming

This is system can arm itself, please make sure that you have pressed UNLOCK button on your original remote.

Because of self-arming, if you forget LOCKING your car when you leave, the system will arm automatically to prevent your carfrom stealing.

Remote Start

Thisis an amazing function, but not all cars support this function, especially cars with aftermarket car alarm systems.

Operation: Just presses the original UNLOCK and LOCK buttons on your remote as a certain sequence.

Advantages:

1. The most important thing is we are the only manufacturer who uses IC for Button Start.

As we know, Button Start system provides power for the car staring section, especially for IG1 and IG2. If the electricity supply of IG1 and IG2 is not stable, the engine can not work well, that is harmful and dangerous. That is why we don't use relays or FAMOS to output electricity to the car wire despite the great cost difference.

2. The system almost consume no electricity when it arming, this means that it won't increase much of your car electricityconsumption.

Installation –How to deal withthe steering lock and RFID immobilizer?

1.Steering lock: the simplest way is copy a mechanical key, insert it into the keyhole and turn it to ON position to keep the steer wheel unlocked, and then cut the outside section, at last, paste the button above it.

2.Original RFID immobilizer: take out the RFID chip from your original remote and paste it the position close to the key cylinder. (Don't worry about your remote; it is independent for most remotes. If the RFID chip is welded on the remote circuit board, don't take it.)