浮选机的应用

浮选机（也称为 浮选分离 ）适用于有色金属和黑色金属和非金属，如萤石和滑石的分离。

叶轮由V型皮带，它可以带来的离心力作用，以形成负压驱动。 一方面，吸入足够的空气混合以矿浆; 另一方面，搅拌矿浆和与药物混合，以形成矿化泡沫。 通过调节闸板高度，你可以控制液面，使由壤土板刮有用的泡沫。

浮选机的工作原理

当浮选机的工作原理，浆料从槽到叶轮之间的空间的底部吸入。 另一方面，通过风扇送来的低压空气在中空轴通过空气分配器发送到这个区域。 充分搅拌后，将浆液被推出由叶轮，然后进入到整个槽。 当泡沫上升到稳定的水平，富集处理后，泡沫溢流到从溢流堰泡沫槽。 矿浆的另一部分流向降低叶轮的部分，用于与空气的再混合。 剩余的浆液流到下一个槽，直到它变成残余物。

操作说明

要检查螺栓开机前，用叶轮的手中，而不是防止沉淀物增加电机的负担。 要调整闸门高度谨慎，以保持液面稳定和刮矿化泡沫的槽。 叶轮和定子应该有一个距离，它们被磨损时应该被改变。 在泵的轴承应该维持每三个月。

浮选机产品特点

1.设计合理

2.高效率

3.低功耗，节能环保

4.易于维护

5.操作简单

SF型浮选机技术参数

Flotation machine application

Flotation machine (also called Flotation separator) is applicable for the separation of nonferrous metal and ferrous metal and nonmetal, such as fluorite and talc.

The impeller is driven by V-belts, which can bring the centrifugal effect to form the negative pressure. On the one hand, to inhale sufficient air to mix with ore pulp; on the other hand, to stir ore pulp and mix with medication to form the mineralized froth. By adjusting the height of flashboard you can control the liquid level and make the useful froth scraped by loam board.

Flotation machine working principle

When flotation machine works, slurry is inhaled from the bottom of the trough to the space between impellers. Meanwhile, the low pressure air sent by fan is sent to this area through the air distributor in the hollow shaft. After sufficient mixing, the slurry is pushed out by the impeller, and then goes to the whole trough. When the froth rises to the stable level, after the enrichment processing, froth overflows to the froth trough from the overflow weir. Another part of ore slurry flows to lower part of impeller for the remixing with air. The remaining slurry flows to the next trough until it becomes residue.

Operating instruction

To check the bolts before starting the machine and to use hands instead of impellers to prevent the sediment from adding the burden of electromotor. To adjust the height of strobe carefully to keep the stabilization of liquid level and scrape the mineralized froth to the launder. The impellers and stators should have a distance and should be changed when they are worn. The bearing in the pump should be maintained every three months.

Product features of flotation cell

1. Reasonable design

2. High-efficiency

3. Low consumption, energy saving

4. Easy to maintain

5. Easy to operate

Technical parameters of SF flotation machine