DC to DC Series LED Driver with Operating Temperature Range from -40 to 85°C, Weighs 2.6g

DC to DC Series LED Driver with Operating Temperature Range from -40 to 85°C, Weighs 2.6g

DC至DC系列LED驱动器,工作温度范围为-40至85°C,重量2.6g

议价

加入意向
  • LED驱动器直流到直流系列,恒流,8W,350mA
  • 8瓦单输出
  • 尺寸20.32×10.16×6.88mm
  • 特征:
    • 适用于高亮度发光二极管产品
    • 符合RoHS标准的14引脚DIL封装
    • 宽输入电压范围:7V至30V直流输入
    • 输出电压范围:(Vin = 30V)2至28V DC
    • 输出电流范围:350mA恒流限制设计
    • 纹波和噪声,(20MHz带宽):最大200mVp-p
    • 高效率(高达95%)
    • 容性负载:47uF
    • 工作频率:40〜370kHz
    • 工作温度范围为-40〜85℃
    • 存储温度:-40〜125℃
    • 最高箱体温度:+ 100℃
    • 表壳材质:非导电黑色塑料(​​UL94-V0级)
    • 保护:短路保护
    • PWM /数字调光和模拟电压调光
    • 重量:2.6g
  • 注意:
    • 反向电源损坏电路
    • 输入地和输出之间不允许连接
    • 不要在8W输出上操作驱动器
    • 如果不使用,请将引脚Vadj打开
    • 将Vadj连接到Vin会损坏电路
  • PWM调光和开/关控制(如果不使用,则保持断开):
    • 远程开/关:
      • DC / DC开:开或0.3V
      • DC / DC关闭:Vadj <0.15V
      • 远程引脚驱动电流(Vadj = 1.25V): <1mA
      • 静态输入电流关断模式(Vin = 30V):最大25uA
    • PWM调光:
      • 推荐最大工作频率:1kHz
      • 最小开关时间:200ns
      • 最小关断时间:200ns
  • 模拟调光控制(如果不使用则保持断开):
    • Vadj输入电压范围:0.3〜1.25V
    • 调整输出电流:25〜100%
    • 控制电压范围限制:
      • On:0.2〜0.3V
      • 关:0.15至0.25V
      • 模拟引脚驱动电流(Vadj = 1.25V): <1mA

  • LED driver DC to DC series, constant current, 8W, 350mA
  • 8 watts single output
  • Size 20.32 x 10.16 x 6.88mm
  • Features:
    • For high brightness light-emitting diode products
    • RoHS compliant 14-pin DIL Package
    • Wide input voltage range: 7V to 30V DC input
    • Output voltage range: (Vin=30V) 2 to 28V DC
    • Output current range: 350mA constant current limiting design
    • Ripple and noise, (20MHz bandwidth): 200mVp-p maximum
    • High efficiency (up to 95%)
    • Capacitive load: 47uF
    • Operating frequency: 40 to 370kHz
    • Operating temperature range from -40 to 85℃
    • Storage temperature: -40 to 125℃
    • Maximum case temperature: +100℃
    • Case material: non-conductive black plastic (UL94-V0 rated)
    • Protections: short-circuit protection
    • PWM/digital dimming and analog voltage dimming
    • Weight: 2.6g
  • Note:
    • Reversed power source damages the circuit
    • No connection is allowed between input ground and output
    • Do not operate the driver over 8W output
    • Leave pin Vadj open if not in use
    • Connecting Vadj to Vin damages the circuit
  • PWM dimming and on/off control (leave open if not used):
    • Remote on/off:
      • DC/DC on: open or 0.3V
      • DC/DC off: Vadj <0.15V
      • Remote pin drive current (Vadj = 1.25V): <1mA
      • Quiescent input current shutdown mode (Vin = 30V): 25uA maximum
    • PWM dimming:
      • Recommended maximum operating frequency: 1kHz
      • Minimum switch on time: 200ns
      • Minimum switch off time: 200ns
  • Analog dimming control (leave open if not used):
    • Vadj input voltage range: 0.3 to 1.25V
    • Adjust output current: 25 to 100%
    • Control voltage range limits:
      • On: 0.2 to 0.3V
      • Off: 0.15 to 0.25V
      • Analog pin drive current (Vadj = 1.25V): <1mA