该灵活的使用非常灵活的PCB丝带高亮度SMD水平安装。 三SMD LED组成一组。 每个组可以根据待切割

长度必需的。 它是在5个计室内使用销售。 LED灯条广泛用作家庭照明，装饰ligting，广告灯等

性能参数

安装和维

安装有3M双面胶带粘，尺寸图如下（单位：mm）

ST3528N60

ST3528N120

接线图

注意

产品应满足“使用环境”requiremetn时，他们的工作。

安装说明

1。 在电源线的选择，电源线应当注意，在当前进行应比正常工作电流所带来的灯大得多。

2。 控制器和开关电源必须工作在通风，干燥的环境中。

3。 确保输入线和控制总线输出线无操作之前短路。 在如短路等工作的情况下，内部元件可能被破坏

注意

1.建议使用长度不超过10米更多LED灯条的连接。 3LED作为一个循环，该接口可以被切割使用，但不能在一个循环的中间切

2.搭配合适的电源按条串联后的总功率，同时还请领导放心适配器的功率必须比负载功率大，否则电源将被烧坏。

3，LED灯条驶过DC12V，请不要使用输出DC5V或DC24V供电，也不会光或烧坏。

4.本产品不防水led系列带钢，适用于室内应用，而不是在雨天或放入水中。

5.软硅胶是在LED表面上，禁止其具有与硅的化学反应的表面上的任何化学溶剂涂抹，否则LED不能发光。

6，工作温度为-10℃°〜+ 40 C°。

7.如果在灯体被破坏，就必须用新的替代。

8.不能连接电源时，在安装或拆卸。

The Flexible is used a very flexible PCB ribbon with high brightness SMD mounted horizontally. Three SMD LED make up one group. Each group can be cut according to the

length required. It's is sold in 5 meter for indoor use. LED strip Widely used as Home lighting, decorative ligting, Advertising lights, etc

Performance Parameter

Installation and dimensions

Installation with 3M double-sided tape to stick, the dimension chart is as follows (unit: mm)

ST3528N60

ST3528N120

Connection diagram

Attention

Product should meet 'use environment' requiremetn when they work.

Installation Instruction

1 . In the choice of power cord, power cord should be noted that the current carried should be larger than normal working current by the lamp brought.

2 . Controller and switching power supply must work in ventilated and dry environment.

3 . Make sure the input wire or output wire of control bus without a short circuit before operation. In the case of work such as short circuit, the internal components may be destroyed

Attention

1. Suggest led strip connection with length no more than 10meters. 3LED as a loop, the interface can be cut to use, but can not be cut in the middle of a loop

2. Collocate suitable power supply according to the total power after strip concatenation, and also pls assure the power of led adapter must be larger than the load power, or else the power supply will be burned out.

3. LED strip drove by DC12V, pls do not use output DC5V or DC24V power supply, it will not light or burn out.

4. This product is non-waterproof led series strip, suitable for indoor application, not in the rain or put into the water.

5. The soft silica gel is on the LED surface, forbid any chemical solvent smear on the surface which have chemical reaction with silicon, otherwise the leds can not light.

6. Working temperature is -10 C °~ +40 C ° .

7. If the lamp body is damaged, it must use the new alternative.

8. It can not connect power when installation or removal.