Smoke and Heat Detector with Relay Output Fire Alarm
烟和热探测器，带继电器输出火灾报警
一般说明：
这种探测器是一个组合的烟雾和热探测器与光电传感器和热敏电阻在一起
该探测器设计用于提供开放区域保护，并与大多数常规火灾报警控制面板一起使用
每个检测器上的两个LED发光，以提供检测器指示的360°可视性
它们每6秒闪烁一次，表示电源已打开，检测器工作正常
LED在报警中锁定
检测器只能通过瞬间电源中断进行复位
启动报警条件的检测器将使其红色LED和继电器锁定，直到面板复位
检测器组合光电子感测室和温度热检测器
特点和优点:
技术规格:
直径：103mm
高度（包括安装基座）：55mm
重量：155g
工作温度范围：-10°C至50°C
工作湿度范围：10％至93％相对湿度，无冷凝
锁定报警：由瞬时电源中断复位
电气额定值:
电源电压：12V DC（9V-28V DC）
待机电流：200μA，12V DC
报警电流：DC12V时为45mA
报警继电器触点额定值：2A，24V DC
烟雾报警灵敏度：1.06±.26％FT
温度报警灵敏度：57°C（135°F）A1R
这种探测器是一个组合的烟雾和热探测器与光电传感器和热敏电阻在一起
该探测器设计用于提供开放区域保护，并与大多数常规火灾报警控制面板一起使用
每个检测器上的两个LED发光，以提供检测器指示的360°可视性
它们每6秒闪烁一次，表示电源已打开，检测器工作正常
LED在报警中锁定
检测器只能通过瞬间电源中断进行复位
启动报警条件的检测器将使其红色LED和继电器锁定，直到面板复位
检测器组合光电子感测室和温度热检测器
特点和优点:
- 兼容所有安全报警系统
- 报警继电器输出（NO / NC可调）
- 无极性输入
- 宽工作电压范围（9-28VDC）
- 独特的光学传感室
- 内置微处理器智能软件
- 两个LED闪烁待机，提供360°可见度
- 防虫筛查
- 扭转安装底座带防拆锁
- 漂移补偿和平滑算法
技术规格:
直径：103mm
高度（包括安装基座）：55mm
重量：155g
工作温度范围：-10°C至50°C
工作湿度范围：10％至93％相对湿度，无冷凝
锁定报警：由瞬时电源中断复位
电气额定值:
电源电压：12V DC（9V-28V DC）
待机电流：200μA，12V DC
报警电流：DC12V时为45mA
报警继电器触点额定值：2A，24V DC
烟雾报警灵敏度：1.06±.26％FT
温度报警灵敏度：57°C（135°F）A1R
General description:
This detector is a combined smoke and heat detector with photoelectronic sensor and heat thermistor together
This detector is designed to provide open area protection and to be used with most conventional fire alarm control panel
Two LEDs on each detector light to provide 360° visibility of the detector indication
They flash every 6 seconds indicating that power is applied and the detector is working properly
The LEDs latch on in alarm
The detector can be reset only by a momentary power interruption
The detector that initiated the alarm condition will have its red LED and relays latched until reset by panel
The detector combine a photo electronic sensing chamber and a temperature heat detector
Features and benefits:
Technical specifications:
Diameter: 103mm
Height (including mounting base): 55mm
Weight: 155g
Operating temperature range: -10°C to 50°C
Operating humidity range: 10% to 93% relative humidity, non-condensing
Latching alarm: reset by momentary power interruption
Electrical ratings:
Power supply voltage: 12V DC (9V-28V DC)
Standby current: 200μA at 12V DC
Alarm current: 45mA at 12V DC
Alarm relay contacts rating: 2A at 24V DC
Smoke alarm sensitivity: 1.06±.26%FT
Temperature alarm sensitivity: 57°C (135°F) A1R
This detector is a combined smoke and heat detector with photoelectronic sensor and heat thermistor together
This detector is designed to provide open area protection and to be used with most conventional fire alarm control panel
Two LEDs on each detector light to provide 360° visibility of the detector indication
They flash every 6 seconds indicating that power is applied and the detector is working properly
The LEDs latch on in alarm
The detector can be reset only by a momentary power interruption
The detector that initiated the alarm condition will have its red LED and relays latched until reset by panel
The detector combine a photo electronic sensing chamber and a temperature heat detector
Features and benefits:
- Compatible with all the security alarm system
- Alarm relay output (NO/NC can be adjustable)
- Unpolarized wire input
- Wide range of operating voltages (9-28VDC)
- Unique optical sensing chamber
- Built in microprocessor intelligent software
- Two LEDs blink standby, provide 360° visibility
- Insect-resistant screening
- Twist-on mounting base with tamper lock
- Drift compensation and smoothing algorithms
Technical specifications:
Diameter: 103mm
Height (including mounting base): 55mm
Weight: 155g
Operating temperature range: -10°C to 50°C
Operating humidity range: 10% to 93% relative humidity, non-condensing
Latching alarm: reset by momentary power interruption
Electrical ratings:
Power supply voltage: 12V DC (9V-28V DC)
Standby current: 200μA at 12V DC
Alarm current: 45mA at 12V DC
Alarm relay contacts rating: 2A at 24V DC
Smoke alarm sensitivity: 1.06±.26%FT
Temperature alarm sensitivity: 57°C (135°F) A1R
