Chinese Energy-Saving Temperature Controller
中国节能温控器
| 型号。 | 达因-848 /达因-868 /达因-878 |
| 定制 | 定制 |
| 类型 | 温度控制器 |
| 规范 | 不等式 |
| 条件 | 新 |
| 输入 | 普遍 |
| 控制类型 | 数字 |
| 起源 | 东莞广东中国 |
产品描述
主要特点：
所有展示都是中文和数字，一般缝纫人员可以阅读和设置。
所有设计简单，只需12个命令。
所有的温差可以在恒温器上设置。具有一定的恒温功能。
4.采用塑料造粒，电线电缆，塑料片，塑料线，塑料管等机械加热冷却。
*当温度高于设定值进行冷却时，立即冷却后的温度低于设定值，绝对节能加热机。
规范：
操作面板和设置说明：
1.按shift键显示：设置温度，其次是黑色。然后按shift键，设置浅红灯，然后按移动键的顶部和底部设置所需的温度。通过设置键确认。
2.按下按钮显示第一个屏幕：加热量，加热停止，加热量。按shift键，加热数量后面的黑色数量，然后按下键，这样再次加热数量后面的黑色数量，按shift键设置浅红灯，
按向上和向下键设置所需的值（1 ---- 20），按设置键使设置指示灯熄灭并设置成功。
3.按下换档键，使加热量再次上升到黑色数量后，按shift键，使加热次数提前加黑量，然后按shift键，
设置灯光，按上下键设置，设定数量小于加热量（1 --- 19）设置为所需值，设置键与设置灯相连（必须设置再次，加热量设定，设定值必须基于生产的材料。枪管的温度和发热量，所有的热量尽可能不发射或少发射）。
4.按shift键加热黑色背后的数字，按下按钮等待黑色数量的加热次数，按shift键设置指示灯，按向上和向下下拉键设置所需的值，（1 --- 180秒）确定设置按钮。
说明：设置温度为180度，加热停止量为2，再加3次加热，加热加热机为30等待量，当机器178度停止加热时，温度降至177度，等待30秒开始加热，停止加热升至178度。
按下按钮显示第一个屏幕：
主要特点：
所有展示都是中文和数字，一般缝纫人员可以阅读和设置。
所有设计简单，只需12个命令。
所有的温差可以在恒温器上设置。具有一定的恒温功能。
4.采用塑料造粒，电线电缆，塑料片，塑料线，塑料管等机械加热冷却。
*当温度高于设定值进行冷却时，立即冷却后的温度低于设定值，绝对节能加热机。
规范：
| 模型 | 电压 | 产品规格 | 其他 |
| DYN-848 | 80---250 | 96*96 | R继电器输出，T电压（DC24V）输出 |
| DYN-868 | 80---250 | 72*72 | R继电器输出，T电压（DC24V）输出 |
| DYN-878 | 80---250 | 96*48 | R继电器输出，T电压（DC24V）输出 |
操作面板和设置说明：
1.按shift键显示：设置温度，其次是黑色。然后按shift键，设置浅红灯，然后按移动键的顶部和底部设置所需的温度。通过设置键确认。
2.按下按钮显示第一个屏幕：加热量，加热停止，加热量。按shift键，加热数量后面的黑色数量，然后按下键，这样再次加热数量后面的黑色数量，按shift键设置浅红灯，
按向上和向下键设置所需的值（1 ---- 20），按设置键使设置指示灯熄灭并设置成功。
3.按下换档键，使加热量再次上升到黑色数量后，按shift键，使加热次数提前加黑量，然后按shift键，
设置灯光，按上下键设置，设定数量小于加热量（1 --- 19）设置为所需值，设置键与设置灯相连（必须设置再次，加热量设定，设定值必须基于生产的材料。枪管的温度和发热量，所有的热量尽可能不发射或少发射）。
4.按shift键加热黑色背后的数字，按下按钮等待黑色数量的加热次数，按shift键设置指示灯，按向上和向下下拉键设置所需的值，（1 --- 180秒）确定设置按钮。
说明：设置温度为180度，加热停止量为2，再加3次加热，加热加热机为30等待量，当机器178度停止加热时，温度降至177度，等待30秒开始加热，停止加热升至178度。
按下按钮显示第一个屏幕：
| 显示 | 范围 | 出厂设置 | 说明 |
| 再次加热 | 0---20 | 2 | 停止加热在设定值以下2度 温度 |
| 加热站 | 0---20 | 1 | 等待在设定温度以下1度的加热 |
| 加热能力 | 0---180 | 10 | 加热量再次加热10秒钟 |
如果加热停止，小数量的温度升高温度上升到设定值
按下按钮显示第二个屏幕：
停止冷却后，温度下降小，数量少，温度下降大，数值较大。
按下按钮显示第三个屏幕：
如果冷却后停止，温度低于设定温度，长时间间隔或冷却时间的小点，温度始终高于设定温度过高，间隔设定较小，或者冷却时间长，可以同时改变两个值，尽量保持不加热。 （有一个加热部分的材料）
转型例子
托马斯光电（东莞）有限公司
两台150台造粒机，六段机身（和模具），加热部分由八部分组成，冷却系统冷却，生产电线电缆材料，转换前每小时电度14度，修改6 Ze世界电子DYN恒温节能温控器耗电2度/小时后，冷却系统良好，加热部分省电率在85％以上，整体节能20％; 70线电线机身四段机身加模，加热部分共四段，冷却系统为空气冷却，生产电线电缆，平均每小时耗电量修改前16.8度，修改4台世界DYN恒温恒温恒温器平均每小时12.9度，一台机器节电3.9度/小时。
沙田塑胶制品有限公司
150个造粒机，机身六段，模头，冷却系统冷却，生产电线电缆材料，消费前12小时不改变，经DYN转换六台Zeshi电子节能温控。电耗为1.1度/小时，加热部分省电率在80％以上。
上海静杰塑胶制品有限公司
是生产窗帘产品。 120型造粒机，风冷，五段和整机模具。
风机前加热功率14度/小时。转换电磁加热功耗为7.5度/小时。省电率在45％以上。
配有5 Ze世界电子DYN恒温恒温恒温器，用电量为1.5度/小时，加热部分省电率在85％以上。
东莞市樟木头南洋化工科技有限公司
双螺杆造粒机为水冷，每吨原料417千瓦时电力生产，采用Zeshi电子DYN节能恒温器，每吨饲料339千瓦时，节电18.7％。
东莞明业包装制品有限公司
2.2米包装机，冷却方式为空气冷却，原来每小时32千瓦时（每天12小时开始），安装了15 Ze世界电子DYN恒温恒温恒温器，每小时14千瓦时，省电率53％。
按下按钮显示第二个屏幕：
| 显示 | 范围 | 出厂设置 | 说明 |
| 开始冷却 | 1---20 | 2 | 等待在设定温度以上2度的冷却 |
| 制冷量 | 0---180 | 10 | 要开始冷却能力，如10秒开始冷却 |
| 停止冷却 | 0---20 | 1 | 在设定温度以上1度停止冷却。 |
按下按钮显示第三个屏幕：
| 显示 | 范围 | 出厂设置 | 说明 |
| 间隔加热 | 0---20 | 10 | 当温度低于10度的设定温度时，开始加热。 |
| 间隔时间 | 1---180 | 5 | 间隔时间5秒开始加热。 |
| 加热时间 | 1---180 | 5 | 5秒后停止加热。 |
如果温度不下降，间隔时间设定小点或加热时间设定一点时间。温度高于设定值，间隔时间设置一点，或加热时间设定为小点，也可以同时更改两个值。尽量保持冷静。 （材料吸收部）
按下按钮显示第四个屏幕：
按下按钮显示第四个屏幕：
| 显示 | 范围 | 出厂设置 | 说明 |
| 间隔冷却 | 0---20 | 10 | 当温度高于设定温度10时间间隔冷却 |
| 间隔时间 | 1---180 | 5 | 5秒后开始冷却。 |
| 冷却时间 | 1---180 | 5 | 5秒后停止冷却 |
转型例子
托马斯光电（东莞）有限公司
两台150台造粒机，六段机身（和模具），加热部分由八部分组成，冷却系统冷却，生产电线电缆材料，转换前每小时电度14度，修改6 Ze世界电子DYN恒温节能温控器耗电2度/小时后，冷却系统良好，加热部分省电率在85％以上，整体节能20％; 70线电线机身四段机身加模，加热部分共四段，冷却系统为空气冷却，生产电线电缆，平均每小时耗电量修改前16.8度，修改4台世界DYN恒温恒温恒温器平均每小时12.9度，一台机器节电3.9度/小时。
沙田塑胶制品有限公司
150个造粒机，机身六段，模头，冷却系统冷却，生产电线电缆材料，消费前12小时不改变，经DYN转换六台Zeshi电子节能温控。电耗为1.1度/小时，加热部分省电率在80％以上。
上海静杰塑胶制品有限公司
是生产窗帘产品。 120型造粒机，风冷，五段和整机模具。
风机前加热功率14度/小时。转换电磁加热功耗为7.5度/小时。省电率在45％以上。
配有5 Ze世界电子DYN恒温恒温恒温器，用电量为1.5度/小时，加热部分省电率在85％以上。
东莞市樟木头南洋化工科技有限公司
双螺杆造粒机为水冷，每吨原料417千瓦时电力生产，采用Zeshi电子DYN节能恒温器，每吨饲料339千瓦时，节电18.7％。
东莞明业包装制品有限公司
2.2米包装机，冷却方式为空气冷却，原来每小时32千瓦时（每天12小时开始），安装了15 Ze世界电子DYN恒温恒温恒温器，每小时14千瓦时，省电率53％。
| Model NO. | DYN-848/DYN-868/DYN-878 |
| Customized | Customized |
| Type | Temperature Controller |
| Specification | inequality |
| Condition | New |
| Input | Universal |
| Control Type | Digital |
| Origin | Dongguan Guangdong China |
Product Description
Main Features:
1. All show is Chinese and digital , general sewing worker can read and set.
2.All design is simple , just 12 command.
3.All the temperature difference can be set on the thermostat. Has a certain constant temperature function.
4.Used in plastic granulation, wire and cable, plastic sheet, plastic wire, plastic pipe and so on need to heat and cooling the mechanical.
* When the temperature higher than set value to cooling , immediately aftercooling temperature is lower than the set value and absolute energy-saving heatingmachine .
Specification:
Operation panel and setup instructions:
1.press the shift key shows: set the temperature, followed by the number of black. Then press the shift key, set the light red light, and then press the top and bottom of the mobile key to set the required temperature. Confirm by setting key.
2. press down the button to display the first screen: the amount of heating, heating stop, the amount of heating. Press shift key,Heating ahead of the quantity behind the number of black, and then press down the key, so that once again the amount of heating up behind the number of black, press the shift key to set the light red light,
Press the up and down keys to set the desired value (1----20), press the set key to make the setting lamp go out and set the success.
3. press the shift key, so that once again the amount of heating up behind the number of black, press the shift key, so that the number of heating in advance of the amount of black, and then press the shift key,
Set the light, press the up and down keys to set, set the quantity is less than the amount of heating (1---19) set to the desired value,The setting key is connected with the setting lamp (must be set up again, and then the heating amount is set, the set value must be based on the material produced.Over temperature and calorific value of the gun barrel, all the heat as much as possible without emission or less emission).
4. press the shift key to heat up the number behind the back of the number of black, press down the button to wait for the number of heating behind the number of black, press the shift key to set the light,Press the up and down keys to set the required value, (1---180 seconds) to determine the settings button.
Explain:Set the temperature of 180 degrees, the heating stop amount for 2, again with 3 heating capacity, heating heating machine with 30 waiting amount, to stop heating when the machine is 178 degrees, the temperature dropped to 177 degrees, wait 30 seconds to start heating, stop heating rose to 178 degrees.
Press down the button to display the first screen:
Main Features:
1. All show is Chinese and digital , general sewing worker can read and set.
2.All design is simple , just 12 command.
3.All the temperature difference can be set on the thermostat. Has a certain constant temperature function.
4.Used in plastic granulation, wire and cable, plastic sheet, plastic wire, plastic pipe and so on need to heat and cooling the mechanical.
* When the temperature higher than set value to cooling , immediately aftercooling temperature is lower than the set value and absolute energy-saving heatingmachine .
Specification:
| Model | Voltage | Specifications | Other |
| DYN-848 | 80---250 | 96*96 | R relay output, T voltage (DC24V) output |
| DYN-868 | 80---250 | 72*72 | R relay output, T voltage (DC24V) output |
| DYN-878 | 80---250 | 96*48 | R relay output, T voltage (DC24V) output |
Operation panel and setup instructions:
1.press the shift key shows: set the temperature, followed by the number of black. Then press the shift key, set the light red light, and then press the top and bottom of the mobile key to set the required temperature. Confirm by setting key.
2. press down the button to display the first screen: the amount of heating, heating stop, the amount of heating. Press shift key,Heating ahead of the quantity behind the number of black, and then press down the key, so that once again the amount of heating up behind the number of black, press the shift key to set the light red light,
Press the up and down keys to set the desired value (1----20), press the set key to make the setting lamp go out and set the success.
3. press the shift key, so that once again the amount of heating up behind the number of black, press the shift key, so that the number of heating in advance of the amount of black, and then press the shift key,
Set the light, press the up and down keys to set, set the quantity is less than the amount of heating (1---19) set to the desired value,The setting key is connected with the setting lamp (must be set up again, and then the heating amount is set, the set value must be based on the material produced.Over temperature and calorific value of the gun barrel, all the heat as much as possible without emission or less emission).
4. press the shift key to heat up the number behind the back of the number of black, press down the button to wait for the number of heating behind the number of black, press the shift key to set the light,Press the up and down keys to set the required value, (1---180 seconds) to determine the settings button.
Explain:Set the temperature of 180 degrees, the heating stop amount for 2, again with 3 heating capacity, heating heating machine with 30 waiting amount, to stop heating when the machine is 178 degrees, the temperature dropped to 177 degrees, wait 30 seconds to start heating, stop heating rose to 178 degrees.
Press down the button to display the first screen:
| Display | Range | Factory setting | Explain |
| Heating capacity again | 0---20 | 2 | Stop heating at 2 degrees below the set temperature |
| Heating stop | 0---20 | 1 | Wait for heating at 1 degrees below the set temperature |
| Heating capacity | 0---180 | 10 | To the heating quantity again, 10 seconds after the heating |
If the heating is stopped, the temperature rise of the small number of smaller, temperature rises to a value set
Press down the button to display the second screen:
After stopping the cooling, the temperature drop is small, the number is small, the temperature drop is big, the numerical value is bigger.
Press down the button to display the third screen:
If you stop after cooling, the temperature is lower than the set temperature, the time interval of a long point or a small point of the cooling time, the temperature is always higher than the set temperature is too much, the interval is set smaller, or the cooling time is long, can the two value change at the same time, try to keep without heating. (there is a heating section of the material)
Transformation example
Thomas photoelectric (Dongguan) Co. Ltd.
Two Taiwan 150 granulator, six section of the fuselage (and die), the heating part consists of eight sections, the cooling system is cooled, the production of wire and cable materials, 14 degrees per hour of electricity before conversion,Modified 6 Ze world electronic DYN constant temperature and energy saving temperature controller after power consumption 2 degrees / h, the cooling system is good, the heating part of the power saving rate of more than 85%, the whole energy saving 20%;70 of the wire and a machine, the four section of the fuselage plus die, the heating part of a total of four sections, the cooling system is air cooling, the production of wire and cable, the average power consumption per hour before modification,16.8 degrees, modified 4 Ze world DYN constant temperature and energy saving thermostat after an average of 12.9 degrees per hour, a machine electricity saving 3.9 degrees per hour.
Sha Tin shaped plastic products Co.
A 150 granulator, six section of the fuselage with mould head, cooling system is cooled, the production of wire and cable materials, no modification before consumption 12 degrees / hour, converting six Zeshi electronic energy-saving temperature control after DYN. Electricity consumption of 1.1 degrees / hour, the heating part of the power saving rate of 80% or more.
Shanghai Jing Jie Plastic Products Co., Ltd.
Is the production of curtain products. A 120 type granulator, air-cooled, five sections and the whole machine die.
Before the fan plus heating power 14 degrees / hour. Converted electromagnetic heating power consumption 7.5 degrees / hour. Power saving rate of more than 45%.
Fitted with 5 Ze world electronic DYN constant temperature and energy saving thermostat, electricity consumption of 1.5 degrees / hour, the heating part of the power saving rate of 85% or more.
Dongguan City Zhangmutou Nanyou Chemical Technology Co., Ltd.
Twin screw granulator is water cooling, and 417 kwh electricity production per ton of raw materials, use Zeshi electronic DYN energy-saving thermostat, per ton of feed 339 kwh of electricity, energy-saving 18.7%.
Dongguan Ming industry packaging products Co., Ltd.
2.2 m packaging model machine, cooling method for air cooling, the original 32 kwh of electricity per hour (starting 12 hours per day), installed 15 Ze world electronic DYN constant temperature and energy saving thermostat, 14 kwh of electricity per hour, power saving rate of 53%.
Press down the button to display the second screen:
| Display | Range | Factory setting | Explain |
| Start cooling | 1---20 | 2 | Wait for cooling at 2 degrees above the set temperature |
| Cooling capacity | 0---180 | 10 | To the beginning of the cooling capacity, such as 10 seconds to start cooling |
| Stop cooling | 0---20 | 1 | Stop cooling at 1 degrees above the set temperature. |
Press down the button to display the third screen:
| Display | Range | Factory setting | Explain |
| Interval heating | 0---20 | 10 | When the temperature is below the set temperature of 10 degrees, the heating is started. |
| Interval time | 1---180 | 5 | Interval time 5 seconds to start heating. |
| Heating time | 1---180 | 5 | Stop heating after 5 seconds. |
If the temperature does not go, the interval time set a small point or the heating time set a little longer. The temperature is higher than the set value, the interval time set a little, or the heating time set a small point, can also change the two values at the same time. Try to keep not cool. (material absorption section)
Press down the button to display the fourth screen:
Press down the button to display the fourth screen:
| Display | Range | Factory setting | Explain |
| Interval cooling | 0---20 | 10 | When the temperature is higher than the set temperature 10 interval cooling |
| Interval time | 1---180 | 5 | Start cooling after 5 seconds. |
| Cooling time | 1---180 | 5 | Stop cooling after 5 sec. |
Transformation example
Thomas photoelectric (Dongguan) Co. Ltd.
Two Taiwan 150 granulator, six section of the fuselage (and die), the heating part consists of eight sections, the cooling system is cooled, the production of wire and cable materials, 14 degrees per hour of electricity before conversion,Modified 6 Ze world electronic DYN constant temperature and energy saving temperature controller after power consumption 2 degrees / h, the cooling system is good, the heating part of the power saving rate of more than 85%, the whole energy saving 20%;70 of the wire and a machine, the four section of the fuselage plus die, the heating part of a total of four sections, the cooling system is air cooling, the production of wire and cable, the average power consumption per hour before modification,16.8 degrees, modified 4 Ze world DYN constant temperature and energy saving thermostat after an average of 12.9 degrees per hour, a machine electricity saving 3.9 degrees per hour.
Sha Tin shaped plastic products Co.
A 150 granulator, six section of the fuselage with mould head, cooling system is cooled, the production of wire and cable materials, no modification before consumption 12 degrees / hour, converting six Zeshi electronic energy-saving temperature control after DYN. Electricity consumption of 1.1 degrees / hour, the heating part of the power saving rate of 80% or more.
Shanghai Jing Jie Plastic Products Co., Ltd.
Is the production of curtain products. A 120 type granulator, air-cooled, five sections and the whole machine die.
Before the fan plus heating power 14 degrees / hour. Converted electromagnetic heating power consumption 7.5 degrees / hour. Power saving rate of more than 45%.
Fitted with 5 Ze world electronic DYN constant temperature and energy saving thermostat, electricity consumption of 1.5 degrees / hour, the heating part of the power saving rate of 85% or more.
Dongguan City Zhangmutou Nanyou Chemical Technology Co., Ltd.
Twin screw granulator is water cooling, and 417 kwh electricity production per ton of raw materials, use Zeshi electronic DYN energy-saving thermostat, per ton of feed 339 kwh of electricity, energy-saving 18.7%.
Dongguan Ming industry packaging products Co., Ltd.
2.2 m packaging model machine, cooling method for air cooling, the original 32 kwh of electricity per hour (starting 12 hours per day), installed 15 Ze world electronic DYN constant temperature and energy saving thermostat, 14 kwh of electricity per hour, power saving rate of 53%.
