RJ45 Gigabit Microwave RF Antenna Poe Surge Arrester
RJ45千兆微波射频天线Poe浪涌避雷器
| 型号。 | WPX-PTSA-2r4-48 |
| 结构体 | 氧化锌避雷器 |
| 应用 | 网络，电信 |
| 工作电压 | 低电压 |
| 材料 | 金属 |
| 牌 | WPX |
| 运输包装 | 每箱1个单位 |
| HS编码 | 8536300000 |
| 类型 | 信号避雷器 |
| 安装 | 壁挂式安装 |
| 尺寸 | 小 |
| 形状 | 广场 |
| 证明 | rohs，iso9001，sgs，ccc，tuv |
| 商标 | WPX |
| 起源 | 中国 |
1000Mbps RJ45千兆Poe户外浪涌保护器
产品介绍：
支持高达1000Mbps的数据速率;所有户外条件下防护等级为IP67;高数据电压保护;杆和墙壁安装套件。
产品展示
规范
| 型号 | WPX-PTSA-2r4-48 |
| 艺术号 | 692 406 |
| SPD类别 | 类型2 |
| 额定工作电压（Uo） | 48V |
| 直流最大持续工作电压（Uc） | 58V |
| AC最大持续工作电压（Uc） | 35V |
| 最大工作电流（IL） | 1A |
| POE电源 | 1,2-3,6或4,5-7,8;总共95W |
| C2总额定放电电流（8 /20μs）（Itotal）tal）tal) | 1.2kA |
| C2标称放电电流（8 /20μs）每根线（In）（In）(In) | 0.3kA |
| 总额定放电电流C2-PE（Itotal） | 20kA的 |
| 每根线C2-PE的额定放电电流（In） | 2.5KA |
| 电压保护等级线线C2（上） | ≤120v120v120V |
| 电压保护等级线PE C2（上） | ≤1000v000v000V |
| 电压保护等级线丝1kV / usC3（上） | ≤90v; 90V;90V |
| 电压保护等级线-PE 1kV / usC3（上） | ≤600v600v600V |
| 响应时间（tA） | ≤1ns;为1ns;1ns |
| 传输速率 | 1000Mbps的 |
| 插入损耗（100MHz） | ≤1.0dB.0dB.0dB |
| 串联阻抗 | ≤0.5Ω0.5ΩOmega;0.5Ω |
| 保护引脚 | 1/2;3/6;4/5;7/8 |
| 相对湿度 | ≤95％（25℃）5℃）dm;C)5ºC) |
| 工作温度范围（TU） | -40℃--- +80ºc-+80ºCrdm;C-+80ºC |
| 气压 | 86kPa ... 106kPa |
| 接线方式 | RJ45（屏蔽） |
| 端口号 | 在-1×RJ45;出1×rj45-1×RJ45s;RJ45-1×RJ45 |
| 外壳材料 | pc / abs ul94 v-0 |
| 安装地点 | 室内或室外 |
| 防护等级（IP代码） | IP54 |
公司展示
产品应用/ 证书
常问问题：
什么是浪涌保护？
浪涌保护是一个浪涌保护器一起工作的系统，以消除一些外部和内部来源的浪涌。在进入的电气，有线/卫星，控制系统和电话公用事业服务中应用浪涌保护器可以防止外部产生的浪涌进入您的办公室或工厂或家庭。适用于敏感电子设备的局部浪涌保护器防止内部产生的浪涌。
我需要浪涌保护吗？
是。现实是，每天都会发生浪潮，并影响家庭，办公室或工厂的设备。通常，浪涌保护归因于“雷电保护”，但事实是，浪涌通常来自公用事故扰动和内部产生的浪涌。工厂或家庭主机因为浪涌损坏而丢失设备是很常见的，甚至没有意识到这一点。许多“神秘”的设备，电脑故障，如设备故障，实际上是由于电涌。此外，由于您认为“正常”磨损的电子设备的故障和更换实际上可能是由于内部或外部引起的浪涌或外部引起的浪涌。
这些干扰发生多久？
因为我们一直使用PLC，交换机，路由器，泵，CCTV系统这么多的东西，频繁发生干扰。
什么是浪涌保护器？
浪涌保护器设计用于将潜在的有害的短时电压峰值安全地从系统中转移到Ground。这在概念上类似于保护热水器免受过压的泄压阀。这是一个常见的误解，即浪涌保护器吸收“浪涌”，实际上它们的目的是将浪涌从受保护的设备转移到地面。到地面
我的电子产品内置浪涌保护。为什么需要更多？
内置的浪涌保护器通常不够强大，无法处理更大的浪涌和尖峰，像其他较小的电涌保护器一样，可以在没有您的知识的情况下磨损，从而无需任何保护。对于一件设备的内置保护可能会给您带来无保护的重要设备，如PLC，电脑，闭路电视系统，SCADA，电话，应答机，调制解调器，打印机等。
我的电涌保护器会持续多久？
在正常操作下，这些设备将无限期地运行。这些设备由WPX（一家通过ISO9001：2008）认证的行业领先制造商设计，可承受多次浪涌事件。我们的世界级测试设备确保最大的设计效率，并确保最大的精度，质量和可靠性。 WPX展示了其对这些产品的信心，为SPD或SPD提供为期1年的产品保修。
如何重置我的Surge Protector？
浪涌保护器不能“重置”。但在一次浪涌放电事件发生后，它将自动复位。
欲了解更多信息和服务，请联系：
联系人：Soniya女士
Mob86 13317313420
网址：www.spdwpx.com
相关热销产品：
http://www.spdwpx.com/a/Products/
| Model NO. | WPX-PTSA-2R4-48 |
| Structure | Zinc Oxide Arrester |
| Application | Network, Telecommunication |
| Operation Voltage | Low Voltage |
| Material | Metal |
| Brand | Wpx |
| Transport Package | 1 Units Per Box |
| HS Code | 8536300000 |
| Type | Signal Type Arrester |
| Installation | Wall Mount |
| Size | Small |
| Shape | Square |
| Certification | ROHS, ISO9001, SGS, CCC, TUV |
| Trademark | WPX |
| Origin | China |
1000Mbps RJ45 Gigabit Poe Outdoor Surge Protector
Product introduction:
Support data rates of up to 1000Mbps; enclosure rating of IP67 for all outdoor conditions; high data voltage protection; Pole and Wall mounting kits.
Product Show
Specification
| Model Number | WPX-PTSA-2R4-48 |
| Art No. | 692 406 |
| SPD category | Type2 |
| Rated Working Voltage( Uo) | 48V |
| DC Max Continuous Operating Voltage( Uc) | 58V |
| AC Max Continuous Operating Voltage( Uc) | 35V |
| Max working current (IL) | 1A |
| POE power supply | 1,2-3,6 or 4,5-7,8 ;Total 95W |
| C2 Total nominal discharge current (8/20μs)(Itotal)tal)tal) | 1.2kA |
| C2 nominal discharge current (8/20μs)per wire(In)(In)(In) | 0.3kA |
| Total nominal discharge current C2-PE(Itotal) | 20kA |
| Nominal discharge current per wire C2-PE(In) | 2.5kA |
| Voltage protection level wire-wire C2(Up) | ≤120V120V120V |
| Voltage protection level wire-PE C2(Up) | ≤1000V000V000V |
| Voltage protection level wire-wire 1kV/usC3(Up) | ≤90V;90V;90V |
| Voltage protection level wire-PE 1kV/usC3(Up) | ≤600V600V600V |
| Response Time(tA) | ≤1ns;1ns;1ns |
| Transmission rate | 1000Mbps |
| Insertion Loss(100MHz) | ≤1.0dB.0dB.0dB |
| Impedance in series | ≤0.5Ω0.5ΩOmega;0.5Ω |
| Protected pin | 1/2;3/6;4/5;7/8 |
| Relative Humidity | ≤95%(25ºC)5ºC)dm;C)5ºC) |
| Working temperature range(TU) | -40ºC---+80ºC-+80ºCrdm;C-+80ºC |
| Atmospheric Pressure | 86kPa...106kPa |
| Wiring methods | RJ45(shield) |
| Port numbers | in-1×RJ45;out-1×RJ45-1×RJ45s;RJ45-1×RJ45 |
| Housing material | PC/ABS UL94 V-0 |
| Installation place | Indoor or Outdoor |
| Degree of protection(IP code) | IP54 |
Company Show
Products Application/ Certificates
FAQ:
What is the Surge Protection?
The Surge Protection is a system of surge protectors working together to eliminate surges from a number of external and internal sources. Applying surge protectors at the incoming electrical, cable/satellite, control system, and telephone utility services keep externally generated surges from entering your office or factory or home. Localized surge protectors applied to sensitive electronics safeguard against internally generated surges.
Do I need surge protection?
Yes. The reality is that surges are occuring daily and effecting the equipment in your home, office or factory. Typically surge protection is attributed to 'lightning protection' but the fact of the matter is that surges are caused most often from utility disturbances and internally generated surges. It is common for factory or home owners to lose equipment due to surge damage and not even realize it. Many 'mysterious' equipment, and computer problems such as devices failure are actually due to electrical surges. Also, breakdowns and replacements of electronic equipment due to what you think of as 'normal' wear and tear may actually be due to internally or externally caused surges.ly or externally caused surges.
How often do these disturbances occur?
Because we use so many things like PLC, Switch, router, pumps, CCTV systems all the time, disturbances happen frequently.
What is a Surge Protector?
Surge Protectors are designed to reduce and divert potentially damaging short-duration voltage spikes safely out of the system to Ground. This is similar in concept to pressure relief valves that protect water heaters from overpressure. It is a common misconception that surge protectors 'absorb' surges when in fact their purpose is to divert the surge away from the protected equipment to Ground. to Ground.
My electronics have built-in surge protection. Why do I need more?
Built-in surge protectors often aren't strong enough to handle larger surges and spikes and, like other smaller surge protectors, can wear out without your even knowing it, leaving you with no protection at all. Built-in protection for one piece of equipment may still leave you without protection for important equipment such as PLC, Computer, CCTV system, SCADA, telephone, answering machines, modems, printers, etc.
How long will my surge protector last?
Under normal operation, these devices will operate indefinitely. The devices have been engineered by WPX, an 'ISO9001:2008' certified industry leading manufacturer and are built to withstand multiple surge events. Our world class test facility assures maximum design efficiencies and assures maximum accuracy, quality, and dependability. WPX demonstrates its faith in these products with a 1-year product warranty for the SPD.or the SPD.
How do I reset my Surge Protector?
Surge protectors cannot be 'reset.' But it will auto-reset after one surge discharge event.arge event.
For more information and Service, please contact:
Contact: Ms. Soniya
Mob86 13317313420
Web: www.spdwpx.com
Related Hot selling products:
http://www.spdwpx.com/a/Products/
