无线充电电动香烟






模块参数：
1.输入电压和电流：DC 9-12 V 1A（可定制输入直流5V）
2.待机功率0.25W-0.5W
3.输出电压：DC 2-6V（默认5V）
4.输出电流：额定600mA Max1000mA
5.输出功率：额定功率3W最大5W
中心谐振频率：125kHz
7.发射器与接收器之间的距离：2-10mm（默认距离4mm）
8.主要应用：
A）游戏周边产品：Wii手柄电池无线双充电，PS3手柄电池无线充电器，xBox360手柄电池无线充电器，NDSi电池无线充电器，NDSL电池无线充电器
B）消费电子：
无线充电电动剃须刀，
无线充电电动牙刷，
无线充电LED手电筒，
无线充电电子防水灯，
无线充电防水手机，
无线充电成人用品，
无线充电电子蜡烛，
无线锂电池充电IC，
无线镍氢电池充电IC，
无线PS3充电器IC，
无线Wii手柄电池充电器IC，
无线NDSL电池充电IC，
无线LED吸引灯电池充电器IC，
无线大灯夜灯电池充电器IC，
无线蜡烛电池充电IC，
无线电子烟电池充电IC，
无线遥控电池充电IC，
无线剃须刀电池充电IC，
无线电动牙刷电池充电IC，电动牙刷，电动剃须刀，电话无线充电。
C）封闭防水产品（潜水设备，泳池产品，手表）
D）数码产品（无线手机充电器，无线iPhone充电器，无线充电MP3，无线充电MP4，摄像头，蓝牙耳机）
E）其他数码产品DIY。
模块尺寸：
A）TX PCB尺寸：24×13×4mm13×4mms; 4mm13× 4mm
B）RX PCB尺寸：14×10×3mm×10×3mms; 3mm10× 3mm
C）线圈尺寸：36mm
D）TX铁氧体尺寸：T1mm *（直径）40mm，RX：40 * 40 * 0.3MM
笔记：
*本模块配置精细铜线圈和进口铁氧体，智能充电管理电路和芯片，全自动待机。确保高功率输出工作效率和稳定性。
*本模块待机电流，输出功率和充电距离可根据您的具体要求进行调整，以达到最佳匹配电路状态！请注意
*使用时，请注意线圈与感应区之间的距离为10 mm，不要放置任何金属或其他导电物体，否则会影响或切断电力传输。不安全
*使用时，保证两个线圈上下对齐，两端铁氧体和两个铁氧体内的两个线圈。保持线圈的最佳使用距离。
*该模块额定输出电压为5 V 600-700 mA。最大输出大于5V 1000 mA。
*产品质量和性能是我们公司的生命，也是我们公司的长期发展理念。为了确保无线充电模块的性能和质量可以与您的产品完美结合，我们使用了可以进行磁体隔离和冷却的铁氧体（线圈下约为USD0.4〜1.0，不能用于许多其他厂商）。考虑到通过EMC和其他安全标识考虑辐射干扰，对电路设计进行了调整。
康妮
奥科科技有限公司


地址：广东省深圳市西乡镇古苏华峰世纪科技园B2栋8楼A座

Wireless Charging Moule for electric cigarette






Module parameter:
1. In put voltage and current: DC 9-12 V 1A (Input DC 5V can be customized)
2. Stand by power 0.25W-0.5W
3. Out put voltage: DC 2-6V (Default 5V)
4. Out put current: Rated 600mA Max1000mA
5. Out put power: Rated3W Max 5W
6. Center resonant frequency: 125kHz
7. Distance between the transmitter and receiver: 2-10mm (Default Distance 4mm)
8. Main application:
A) Game periphery product: Wii handle battery wireless double charging, PS3 handle battery wireless charger, xBox360 handle battery wireless charger, NDSi battery wireless charger, NDSL battery wireless charger
B)Consumer electronics:
Wireless charging electric shaver,
Wireless charging electric toothbrush,
Wireless charging LED flashlight,
Wireless charging electronic waterproof lamp,
Wireless charging waterproof mobile phone,
Wireless charging adult products,
Wireless charging electronic candle,
Wireless lithium battery charging IC,
Wireless Ni-MH battery charging IC,
Wireless PS3 charger IC,
Wireless Wii handle battery charger IC,
Wireless NDSL battery charging IC,
Wireless LED appeal lamp battery charger IC,
Wireless mostones night lamp battery charger IC,
Wireless candle battery charging IC,
Wireless electronic cigarette battery charging IC,
Wireless remote control battery charging IC,
Wireless shaver battery charging IC,
Wireless electric toothbrush battery charging IC, electric toothbrush, electric shaver, telephone wireless charging.
C) Closed waterproofing product (diving equipment, pool product, watch)
D) Digital products (wireless cell phone charger, wireless iPhone charger, wireless charging MP3, wireless charging MP4, camera, Bluetooth headset)
E) Other digital products DIY.
Module Dimension:
A) TX PCB Dimension: 24× 13× 4mm13× 4mms; 4mm13× 4mm
B)RX PCB Dimension: 14× 10× 3mm10× 3mms; 3mm10× 3mm
C)Coil Dimension: 36mm
D)TX ferrite Dimension: T1mm* (diameter)40mm, RX: 40*40*0.3MM
Notes:
*This module configuration of fine copper coil and imported ferrite, intelligent charging management circuit and chip, full of automatic standby. Ensure high power output work efficiency and stability.
*This module standby current, output power and the charging distance can be adjusted according to your specific demands, in order to achieve the best matching circuit state! Please note
*When used, please note between coil and around inductive zone 10 mm, do not place any metal or other conductive objects, it can affect or cutoff electricity transmission. And unsafe.
*When used, guarantee the two coils on up and down aligned, the two ferrites at both ends and the two coils inside the two ferrites. Keep the coil of best use distance.
*This module rated output voltage 5 V 600-700 mA. The maximum output is greater than 5V 1000 mA.
*the product quality and performance is the life of our company, also our company's long-term development concept. To ensure that the wireless charging module performance and quality can be combined perfectly with your product, we used ferrite which can magnet isolated and cooling (under coil, about USD0.4~1.0. Not be used from many other venders). The circuit design is adjusted considering to pass the EMC and other safety identification of worrying of the radiated interference.
Connie
Aoke Technology Co., Ltimied


Address:8F A, B2 Building, Huafeng Century Science and Technology Park, Gushu, Xixiang Town, Shenzhen, Guangdong, China