Product Name: Mini Pocket Pocket Scale

Range: 500g / 0.01

Accuracy: 0.01g

Automatic shutdown: 3 minutes automatic shutdown

LCD display: 3 LCD display

Power: a button electronic

Scale body size: 9X5.5X2cm

Stainless steel weighing pan Size: 5.5X5cm

Unit selection: g / oz / ct / gn

Green backlit display

Use:

1, the maximum weighing of this product should not exceed its maximum range + 2%.

2, the overload will permanently damage the product.

3, the product can not be exposed to extremely cold or extremely hot environment, in the normal environment of the product can work well, please use before the product in a new environment to adapt at least one hour.

4, before use, start weighing several times with the weight of the internal components to warm up the scale, this will make weighing more accurate.

5, the product on a clean environment, dust, moisture, vibration, airflow, or electromagnetic interference will have a negative impact on the stability and accuracy of the product.

To gently handle, weighing items should be gently placed on the weighing pan, so as not to inaccurate weighing or damage to the internal parts of the scale.

6, because the product is a high precision products, so use very carefully, to avoid vibration or drop.

7, in a stable windless level to use.

Second, the operating instructions:

Place the battery correctly in the battery compartment and place it on a smooth, windless countertop.

1, press the power button to boot, wait three seconds display 0.1 or 0.01;

2, will be on the scale to be on the weighing plate, to be stable after the number of readings;

3, according to the unit conversion key to change the measurement unit;

4, the boot state press the power button shutdown;

Third, the deduction weight:

1, according to the above steps boot;

2, the buckle on the weighing plate;

3, press the peel key to display 0.1 or 0.01, that has been deducted;

4, and then put the goods to be weighed, this time the reading is the net weight of items.

Fourth, the correction:

1, boot to zero;

2, hold down the unit conversion key until the display CAL, press the unit conversion button, flashing weight value;

3, the corresponding weight on the pan in the middle, later, display PASS, and then display 100.00g, calibration is completed, remove the weight, you can weigh.

Fifth, troubleshooting:

Weighing Inaccuracies or Faults Primary Factors Battery is low, calibrated incorrectly, overloaded or operated on a non-horizontal level Please note the points mentioned above to properly use and maintain your product.

1, do not show or display the power shortage symbol 'lo' need to change the battery;

2, 'EEEEE' overload, should immediately remove the overloaded items;

3, 'o_ld' If the internal core of the scale is damaged (eg impact, drop or overload) due to incorrect operation, try recalibrating and re-calibrate if the sensor is not severely damaged.

4, display 88888, please work in a vibration-free, stable plane.

The range: (appearance of the same)

100 g / 0.01 g 200 g / 0.01 g 500 g / 0.1 g 1000 g / 0.1 g

Bit seven-segment liquid crystal display, automatic shutdown ① range;

② high sensitivity, fast response, the use of imported weight sensor scale, reflecting the faster and accurate return to zero;

③ stainless steel scale surface;

④ calibration method is simple, just a few simple operation, you can calibrate the scale is very accurate;

⑤ power, using two 7 batteries, the replacement is more convenient;

⑥ automatically turn off the organ backlight function, automatically turn off the power when idle;

⑦ peeled and multi-unit optional function Range / division value: 1000g / 0.1g

Auto power off: 3 minutes automatic shutdown LCD

Display: 5-digit LCD display

Power supply: 2 * 'AAA' battery

Overall dimensions: 114 * 76 * 19.5mm

Stand-alone weight: 116g

Large stainless steel tray: 73 * 65MM will be placed in a stable table

1. Press 'on' key, wait for 5 seconds to display 0.0;

2. Put the weight on the tray surface, when sitting angle 's' appears, is the weight of heavy objects;

3. Use the MODE key to change the unit of measure, g / oz / ozt / dwt / ct;

4. Press TARE to force zeroing
Correction method:

Press the on button for 3 seconds, the display no display, wait 3 seconds display 0.0 to let go, and display 100 grams, then placed 100 grams of weight on the tray, 3 seconds after the automatic shutdown, calibration is completed, press the key to boot '0', with 100 grams of weight weighing calibration, (due to excessive temperature, or other reasons for weighing please use this feature.

Manufacturers to produce direct. Welcome to inquire

Factory direct contact QQ: 2880895121

Mobile: 15207945959

The company's products are all really making plans to welcome to come to the Advisory

The company's products are all really making plans to welcome to come to the Advisory

Contact QQ: 2880895121

Mobile: 15207945959