Dual-use network cable clamp, multi-function, durable, is the information age, the modern family standing tool.
Can produce RJ45 network line connector, RJ11 telephone line connector, 4P telephone line connector.
Integrated network cable clamp all the features, can be easily cut off, pressure lines, stripping and other operations.

Product Features:

- Product function is complete, practical good

- Compatible with different plugs, cards, modules and patch panels

- With card, cut, cut, play multi-functional adaptation

- The use of high-quality steel, reasonable design, effort, fast, long life

8p8c / 6p6c / 4p4c / net pliers, can be made 8-pin network cable and four-core telephone line crystal head. Dual-use multi-function integrated network pliers all functions, can facilitate the network cable (telephone line) cut, pressure lines, stripping and other operations .

Crystal head connection:
Tools: net pliers
TIA / EIA568B. In the line should be used in the following order: (TIA / EIA568B), the color of the color of the twisted pair and the alignment method is a unified international standards strictly defined, now commonly used is TIA /
1- & gt;
2-> orange
3-> green and white
4-> blue
5-> blue and white
6-> green
7-> brown white
8-> brown
Moreover, the use of one-to-one cable at both ends of the connection,
Will make a group of signals (negative voltage signal) is not twisted together through the two core transmission, resulting in a great near-end crosstalk (NEXT->
Near-end-crosstalk) so should be in line with international standards!
Step: First, we use the crimping pliers to cut out the need to use to cut the length of the twisted pair.

Step 2: We need to twist the gray protective layer stripped, you can use the crimping pliers to the thread cutting edge of the thread will be cut together, then thread into the stripping special knife-edge, a little hard grip clamp Slowly rotating, so that the knife-edge to open the protection of twisted-pair rubber.To remove part of the protective rubber in this step should be noted that the pressure clamp from the stripping knife blade length is usually just the length of the crystal head, so you can Effective to avoid stripping too long or too short.If the stripping is too long looks certainly not beautiful, on the other hand because the cable can not be stuck crystal head, easy to loose; if the stripping is too short, due to the existence of protective layer of plastic , Can not be fully inserted into the crystal head at the bottom, resulting in the first crystal pin can not be in good contact with the network cable core, of course, will affect the quality of the line.

The third step: we need to put each pair are intertwined with each other one by one to solve the cable.After the solution according to the need to wire the rules of several groups of cables arranged in order and straighten out, when the arrangement should be noted that as far as possible Avoid winding and overlapping lines.

Step 4: We put the cable in order to straighten and straighten the straight, you should carefully check it again, after the pliers of the sharp line of cutting force to cut the top of the cable neatly cut, it should be noted that the cutting should be horizontal Insert, or cable length will affect the cable and the crystal head of the normal contact.If the protective layer before stripping too much, you can here will be too long to cut short thin lines, retaining the outer layer to remove the protective layer Is about 15mm, the length of the fine wire can be inserted into their respective trough.If the segment to stay too long, the one will be no longer because of the twisted pair to increase crosstalk, and secondly because the crystal head Can not suppress the sheath and may cause the cable from the crystal head in the prolapse, resulting in poor contact or even interrupt the line.

Step 5: We need to do is to put together a good cable into the crystal head.It is important to note that the crystal head with plastic material spring side down, there is a pin on the direction, so that the end of a pin pointing At this time, the left is the first one foot, the right is the first eight feet, followed by the order of the rest. Insert the time need to pay attention to slowly put the 8 The cable is inserted along the eight trunks in the RJ-45 header, and is inserted into the top of the trunking.

Step 6: of course, is the pressure line, and confirm the correct crystal head can be inserted into the crimping pliers 8P tank pressure line, the crystal head inserted, the force grip wire pliers, if the strength is not enough, you can use both hands Together with the pressure, so that the pressure of the process of making a crystal head protruding out of the pin all the pressure into the crystal and head, after the force heard a slight 'snapped' sound