EP-110 cat is a pure fiber modem Modem, with no wireless integrated access functions

Guide for selection of cat:
1: determine the optical system is GPON, EPON still, two systems cannot be generic, be sure to be sure.

2: cats with phone interface, without a telephone interface.

3: cat used for the first time, must be set to not Plug and play, make sure your local installation staff willing to help you set up, you can also consult our instructions later in the Configuration Guide (see the following figure).

If not, you can call our technical support line 400-8863-400, light cat Service Center.

This baby only applies to mode EPON fiber-optic network, please buyers confirm the fibre meets this condition, buy

Also need to verify that the installed fiber-optic network operator restrictions (can only be used a particular brand or model of fiber optic cats)! If you have limited

Buyers Seriously buy .As a result of the above causes the return of buyers you want two-way bear the freight, you know!!!

This article describes EPON TL-EP110 V2.0 product configuration process in detail.

Note: Use EPON Products Prior to first confirm whether local fiber-optic lines to operators for EPON Line, and whether the operator allows users to buy fiber optic modem access (operators in some areas do not allow users to purchase and installation PON Products) .

A physical connection

As shown in the following figure, home fiber insert TL-EP110 V2.0Fiber-optic interface computer using a network cable connected LAN . Connection when turn on the power, Equipment The Power Lights, LAN Lights are always.

If after a period of time, TL-EP110 V2.0The LOS Light is illuminated steady or blinking (red), then an exception is representative of fiber-optic lines, please check the device connection to the fiber is normal, and contact with operators to make sure the line is EPON Line, and the current circuit is normal.

Second, configure the computer's network parameters

Typically, after the physical line connected, Fiber optic modem Connect computer Internet access does not immediately need to Equipment After the settings are made. If you want to set EPON Product, you need to first specify the computer cable adapter IP Address for 192.168.1.X (XFor 2-253) To login to TL-EP110 V2.0 management interface.

Third, set the EPON products

After you set the computer's IP address, open a browser and enter in the address bar: 192.168.1.1 enter, in the pop user name and password boxes, enter the default user name and password admin To log in after TL-EP110 V2.0 management interface.

EPON products after connecting fibre must be operators office equipment on the front of a certification, registration process before it can be normal access to the Internet. Different operators in different areas of certification, registration is not the same way, set up the EPON products please confirm PON and operator product certification.

Current major EPON certification LOID certification, MAC certification. LOID most common, the paper also LOID certification for example.

Log in to the admin interface, click on the 'Internet access settings ' Select LOID certification, saved after input by the operator provided by LOID (Note must be case-insensitive, or may even cause the registration is not successful, some areas need a LOID password besides LOID, specific to operators to provide information shall prevail).

After entering LOID wait, TL-EP110 V2.0 PON led changes from flashing to constant light, this light cat and a front-end device registration successful. Using a computer or router after EPON can access in accordance with operator (for example PPPoE dial, dynamic IP, and so on) the Internet.

Four, for VLAN settings

Usually operators on the fiber-optic line will open up a wide variety of business, such as broadband Internet access services, IPTV service, voice telephone services, to distinguish between the different business operators are often in a different VLAN to differentiate.

While EPON PON always was, some areas may appear a computer or router couldn't get dial-up Internet access, which may be related to VLAN mode line, you can do the following:

In the PON lights stay lit after landing TL-EP110 V2.0 management interface, click on the 'VLAN detection ' Detect button in the page, and see if we can detect valid information.

If it detects a valid VLAN value, click on the 'Internet access settings ' Fill in the VLAN settings option to detect VLAN value (if there is more than one VLAN, you can try) and saves the reboot and then test a computer or router can dial-up Internet access.

If no VLAN value is detected, you can try to set the VLAN mode to 'VLAN passthrough ' Save and restart and test computer or router can dial-up Internet access.

If the above steps do not solve the problem, contact the operators recognize the VLAN information or contact TP-LINK technical support hotline at 400-8863-400.