Medical Equipment Baby Warmer H-1000 Infant Incubator

900-1000 USD

Model NO.	H-1000
Certification	CE
Group	Infant
Medical Devices Reg./Record No.	Gsyjxz20123540587
Temperature Rise Time	≤30min30min0min
Temperature Uniformity	≤1°ce;1°cg;ce;1°c
Trademark	Healicom
Origin	China
Type	Infant Incubator
LCD Display	Without LCD Display
Medical Device Regulatory Type	Type 2
Temperature Control Mode	Air Control
Temperature Variability	±0.5°csmn;0.5°cg;csmn;0.5°c
Air Temperature	20°c~37°cc~37°cg;cc~37°c
Specification	ISO
HS Code	90189090

Standard Composition:
1. Servo Control Mode: air temp;
2. Instant Parameter Displaying: set temp, air temp and heat power rate;
3. Audible & Visual Alarms: power failure, sensor failure, higher & lower temp, air temp override, fan failure, system failure; failure; failure;
4. ﹥37°C Preset Mode: power failure reset memory, alarm silence, keypad lock, self-test function;unction;tion;
5. Hood with dual slope: 6 hand-ports; left & right cabinets, top-shelf;helf;helf;
6. RS-232 Output Connector (Use for network system )
Specification:

Power	Model H-1000-1E		110 / 120 V ac, 50Hz / 60Hz
	Model H-1000-2E		220 / 240 V ac, 50Hz / 60Hz
	Power Input		≤400VA00VA00VA
	Refer to IEC60601-1, this equipment belongs to ClassI, Type BF Its operation is continuous
Alarm	Power Alarm	Power Failure: Activates if primary power to the Incubator fails or the power wire is accidentally disconnected from the wall receptacle
	Fan Alarm	Fan Failure: Activates if Fan motor malfunctions
	Sensor Alarm	Air Sensor Failure: Air Sensor malfunction, refer unit to service
	Deviation Alarm	High Air Temperature: Activated if displayed Air Temperature is 15°C above set pointpointpoint
		Low Air Temperature: Activated if displayed Air Temperature is 25°C below set pointpointpoint
	Over Temperature Alarm	Over Air Temperature: Activated when displayed Air Temperature was approach 38°C for set temperature ≤37°C, or approach 40°C for set temperature ﹥37°C in Air Modegt;37°C in Air Modeegt;37°C in Air Mode
	System Alarm	System Failure: Activated if Temperature Control System malfunctions
Temperature Control Range and Correlative Specifications	Air Temperature			20°C~37°C,for set temperature ≤37°C, 37°C~39°C, for set temperature ﹥37°Cor set temperature >37°Ceg;Cor set temperature >37°C
	Temperature Rise Time			≤30min0min0min
	Temperature Variability			±0.5°Cmn;0.5°Ceg;Cmn;0.5°C
	Temperature Uniformity			≤1°C;1°Ceg;C;1°C
Environment Requirement	Environment Temperature			Operation Temperature Range	+20°C~+30°C+30°Ceg;C+30°C
				Store Temperature Range	-40°C~+55°C+55°Ceg;C+55°C
	Environment Humidity			Operation Humidity Range	30%~75%
				Store Humidity Range	10%~100%
	Atmospheric Pressure Range			700hPa~1060hPa
Other Specifications	Noise Level Within Hood Environment			≤55dB(Environment noise below 45dB)5dB)5dB)
	Carbon Dioxide (CO2) Level within the Hood			Less than 0.5% when a mixture of CO2 in air is delivered at 750ml/min at a point 10cm above the center of the mattress
	Air Velocity Over Mattress			less than 0.3m/s
	Infant Bed Max Load			10kg
	Transfusion Shelf Max Load			2kg
	Cabinet Max Load			6kg
Function of 'SILENCE' KeyE" Keyt; Key	Make the alarm to be silence for 10 minutes by press this key			Deviation Alarm
				Sensor Alarm
				Fan Alarm
Factory Default Settings	Temperature Control Mode Air Temperature Mode
	Air Set Temperature: 32°Cdeg;Cdeg;C
	Temperature Units:°Cdeg;Cdeg;C

NOTE: Open Access Panel or Access Door or the use of supplies or other equipment within the Incubator, which can alter the air flow pattern, may effect temperature uniformity, temperature variability, the correlation of the Incubator temperature reading to center mattress temperature and skin temperature.