Small shoe, shoe repair machine, can sew a variety of size cloth shoes, shoes, shoes, travel bags, raincoats, etc.

Simple structure, compact and lightweight, high efficiency, welcomed by shoemaker

Binding machine instructions

structure
1. Needle bar rocker 14. Line pick

2. Small connecting rod 15. Line pickers

3. Large rocker arm 16. Line care

4. Small rocker 17. Winder

5. Needle 18. guide plate

6. Needle 19. Waving hands

7. Presser foot pressure adjusting nut 20. Spindle

8. Needle pitch adjustment nut 21. Shaft

9. Presser foot 22. Suto

10. Pressure plate assembly 23. Shuttle

11. Bobbin 24. Bobbin

12. Wrench 25. Tie rod

13. Live block

Use and maintenance:
Bucket movement parts need to refuel once a day, can ensure that the machine running light, no noise, improve work efficiency and extend service life.

Preparation before operation: Raise the presser foot to avoid friction between the presser foot and the needle plate, check the tightening of the Ministry of fixed screws, the Ministry of oil with oil, shake the guide plate without the sound can be used.

Threading and Leads:

Take the shuttle and bobbin, shaking guide plate, the needle rose to the highest position, remove the shuttle with tweezers, lift and push the needle plate, with tweezers remove the shuttle

Bobbin winding:

Pull the winding machine, take out the thread around the bobbin set into the reel a few weeks, shake the guide plate to be around full remove the bobbin, , The colleague will be bobbin embedded shuttle, and then thread head to the thread hole, pull the line is active. Release position is the hand guide plate, the needle just to rise, the shuttle tail to align the needle slot, and Thread out 2-3 inches long, according to a half-moon lattice and then shut the tank on the needle plate

Wearing thread:
Shake the guide plate, raise the needle to its highest position, and lower the presser foot. (Not too tight), with the right hand along the guide plate, on the needle and thread through the needle plate hole leads to the bottom line, and Place the bottom line together to make the presser foot gap to the left rear.

The Relationship between Bottom Limit and Quality of Mending:

Stitch identification, adjustment and the bottom line pressure, the upper thread tight loose loose line nuts, the use of time is too long, there will be the bottom line outlet too fast, this time adjustable thread pierced or bobbin, the bottom line tight thread Rod seat fixing screw to relax, pick the needle bar to push back, and then check the bobbin rotation is flexible, sandpaper sanding, tighten the pressure line nut pitch adjustment, due to the different sewing materials need to adjust the pitch, It is only necessary to loosen the needle from the screw, in the selection of the needle from the short, and then move up, you can. In the case of sewing thick pieces, the pressure must be increased, then the presser foot spring Tight, increase the tension of the tension spring, it will increase the pressure on the pressure foot, and vice versa to reduce.

Needle handling and sewing materials with:
Rotate the guide plate so that the needle bar is raised to the highest position. Loosen the needle chuck screw, remove the old needle, insert the new needle flat face into the needle bar groove, and touch the needle on the needle Can be.

Needle and sewing material:

The general use of 16-pin, sewing a variety of shoes and wrapping shoes and other thinner with 14-16 needle, sewing a variety of shoes and canvas and other thicker with 18-pin

Adjustment of the shuttle position:

In the back shuttle that off-line, the tail of the shuttle must be aligned at the needle groove, the difference is a lot of distance, is the location of the shuttle misplaced, not to be adjusted when loosening the live block and tie rod link screw, The tail of the needle groove can be aligned in the tightening screw up and down the adjustment, in the needle stage, the needle hole should be aligned with the base plate plane, or should be adjusted, is to release the small connecting rod shaft screw, To the correct location and then tighten.

Buyers before buying / Tips

Tips: In order to make this purchase a pleasure, please be patient to read the following notes and statements, when you buy our products, the default acceptance of the following agreement

About commodities:

OUR product price is not including tax prices.

About delivery:

1. Delivery time: OUR will pay the customer within 48 hours after the successful delivery of products

2. Shipment preparation: Before shipment, we will test the machine, to ensure product quality, and carefully check the product packaging to ensure that the goods issued before the goods intact.

3. A product generally used express delivery, more than one wholesale logistics transport, the specific mode of transport can contact us

about delivery:

1. What Express: the default delivery through courier.

2. Express delivery: because the products are heavy goods, express delivery may cause damage on the way, so please customers in the receipt of goods must be carefully checked, if damaged directly rejected, and contact us. If the customer after the receipt Check the product, there is any damage to the product to be replaced, back and forth freight borne by the customer.