The angle of repose tester / alumina bulk density meter / analyzer angle of repose of aluminum fluoride / aluminum fluoride fluidity measurement apparatus / repose angle meter / bulk density aluminum fluoride / Angle of repose of aluminum fluoride / Bulk Density Tester / flow measuring device / repose angle measuring device

FT-104 alumina bulk density tester

First, based on compliance with GB / T 6609.25-2004 (Alumina chemical analysis methods and determination of physical performance bulk density determination) Technical Specification determination alumina chemical analysis methods and determination of physical performance bulk density Part 25 of

two, FT-104 alumina bulk density tester Technical Parameters:

1. Funnel: mouth diameter 100mm, taper 60º, within the discharge port by 6mm.

2. cylinder: about 200ml, the inner diameter of the inner high ratio of 1: 6, the base outer diameter of 70mm

3; Material: Stainless steel

FT-104A alumina repose angle measurement

(Alumina chemical analysis methods and determination of physical performance: Determination of repose angle) in accordance with national standards GB / T6609.24-2004 designed and manufactured for measuring the angle of repose of the powder under natural flow conditions.

Stainless steel funnel: The inner diameter of 74mm, 6mm inside diameter of the feed opening

Weight: about 16kg

FT-104B angle of repose tester

FT-104B repose angle measurement is based on GB11986-89 (surfactant powders and granules measuring the angle of repose) provides the design. The instrument is suitable for the angle of repose no clumps of powdered or granular surfactant and detergent The conventional assays can also be used measuring the angle of repose of a similar nature and other powder particles.
Disc: diameter 10MM
Funnel: diameter 155mm inner diameter of 145mm

Aluminum fluoride fluidity measurement apparatus

Funnel: stainless steel outer diameter of the funnel catchy 138.5mm, an inner diameter of 123mm, outlet diameter is 3.95mm ~ 4.0mm, the total height of 190.5mm wear resistant stainless steel catchy taper:. 60 °, the feed opening taper 15 °.

Aluminum fluoride bulk density measuring device

Bulk density measuring device , Including the following sections:

1, Funnel: upper inlet diameter 100mm, taper 60 °, neck length 8mm, brought in under the spout inside by 6mm.

2, cylindrical containers: volume of about 200mL, Nei Jing and about 1 in the high ratio: 6, the inner bottom is flat.

3, the annular funnel rack: There are pillars in the bottom stage of sturdy funnel annular mounting frame, long screws fixed to the pillars of the ring frame, and can be freely adjusted.

The funnel installed in the cylindrical container above the predetermined level surface.

Angle of repose of aluminum fluoride measurement device

Angle of repose measuring device Mainly includes the following components:

1, stainless steel funnel: Neijing 74mm, inside through between the feed opening 6mm, two steps of aperture plate fitted with a sieve of 1mm This funnel is fastened to the bracket.

2, galvanized steel plate: material made of steel or marble, stainless steel and other corrosion-resistant base plate is made, the minimum size of: Width 200mm, length 270mm, 18mm thick plating on the polished floor of the four cross engraved on the surface 45. Angle straight. right in the center section of the funnel has a fixed height gauge positioning pin, the bottom plate below 3 adjustable horizontal feet.

3, Funnel Holder: composed of stainless steel, its structure should be perpendicular to the centerline of the fastening funnel centering pin.

4, height gauge (determine the height of the metal cylinder): It is a cylinder surface finish made of stainless steel, high 40mm, the bottom has a recess so that the center of the bottom plate with the locating pin convergence.

The angle of repose tester bulk density gauge repose angle measurement

The angle of repose tester bulk density gauge repose angle measurement

The angle of repose tester bulk density gauge repose angle measurement