Whether to provide custom processing: Yes	The scope of products: Hall flow meter
Whether to provide custom processing: Yes	The scope of products: Hall flow meter

FL4-1 flowability and bulk density measuring device (brass) Bulk density measuring bulk density measuring device

Where can freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability. Powder flowability to 50g metal powder to flow through a standard funnel needed to represent.

We also accompanied by 100 g GBW12004 national standard level for calibration equipment.

In addition to the aperture of 2.5mm standard funnel, we also provide a pore size of 5.0 standard funnel.

Where can freely flow through the aperture of 2.5mm, 5.0mm standard funnel powder can use this instrument to measure the metal powder bulk density.

The instrument according to GB1479-84, GB1482-84 Standard Specification for production.

FL4-1 flowability and bulk density measuring device for measuring powder flowability and bulk density, this instrument is equipped with a metal powder flowability measurement standard substance with emery GBW12004.
Under funnel diameter: φ2.5㎜ and φ5.0㎜

Angle: 60 degrees
Capacity: 25 ml ℃ Contact Zeng Sheng Phone: 15088416993

FT-102 Hall flow meter flow and bulk density measuring device (stainless steel material)

Foreword

FT-102 Hall flow meter is based on national standards GB 1482-84 The provisions of the design and production. The device is suitable metal powder flowability measurement standard funnel in. Where can freely flow through the aperture to 2.5mm Standard funnel powder, can use this device.

1, the principle

Metal powder flowability to 50g Time metal powder to flow through a standard funnel predetermined aperture required to represent.

2, the instrument structure

2.1 funnel ( Hole diameter 2.5mm)

Funnel made of stainless steel, and has a sufficient thickness and hardness to prevent deformation and excessive wear.

2.2 Bracket, base and receiver

Bracket for fixing the funnel. Base for mounting bracket and receiver, adjust the level, stable and vibration free. Stand height adjustment and fixed with the supplied wrench, funnel attached to the bracket. Receiver (Stainless steel plate) is placed in the base on to collect powder.

2.3 Balance (user-supplied)

Maximum weighing 100g ; Accuracy 0.05g .

2.4 Stopwatch

Measurement time can be accurate to 0.01s .

2.5 Graduate

The device is equipped with a volume of 25ml The stainless steel measuring cup. Users can refer GB GB 1479-84 The provisions of the completion of the metal powder density determination (funnel) loose.

3, the basic configuration

	name	Models and Specifications	The number of
1	The stand	FT - 102	1 set
2	funnel	Stainless steel (Φ 2.5mm Or Φ5.0mm)	1 only
3	Amount Cup	Stainless steel (Φ 31mm , 25ml )	1 only
4	Bracket	stainless steel	1 only
5	Stopwatch	ZSD-809 ( Electronic stopwatch)	1 only
6	Overflow trays	stainless steel	1 only
7	wrench	4mm inner hexagon	1 only
8	brush		1 only

FT-103 natural deposition method bulk density meter

FT-103 type of natural deposition method bulk density meter is based on the provisions of the national standard GB / T 16913.3-1997 design and production. This device is suitable for determining the density of dust accumulation.

Please refer to the sample collection GB / T 16913.1-1997 dust Physics Experiment Part 1: Dust samples collected in the relevant regulations.

1, the principle

Dust from the funnel mouth full of free fall at a certain height measuring cup; mass per unit volume of dust inside the cup measured bulk state, that dust bulk density.

2, the instrument structure

2.1 funnel (flow outlet diameter 12.7mm)

Funnel made of stainless steel, which funnel taper of 60 ° ± 0.5

2.2 jamming bars

Stainless steel, used to prevent dust falling when the dust loading funnel.

2.3 Balances (user-supplied)

The largest weighing 100g; precision 0.02g.

2.4 cups

The device is equipped with a volume of 100ml stainless steel cup, cup inner diameter Φ39mm.

2.5 Scraper

Stainless steel, used to remove excess dust when the dust loading funnel.

3, the configuration

	name	Models and Specifications	The number of
1	Hydrometer host	TF-103	1 set
2	Jamming bars	stainless steel	1
3	Cylindrical cup	Stainless steel (Φ39mm, 100ml)	1
4	Scraper	Stainless steel (120mm)	1
5	brush	15mm	1

FT-104 alumina bulk density tester

First, based on compliance with GB / T 6609.25-2004 (Alumina chemical analysis methods and determination of physical performance bulk density determination) Technical Specification determination alumina chemical analysis methods and determination of physical performance bulk density Part 25 of

Second, the technical parameters

1 Instrument main parts:

2 stainless steel chassis: 210 * 140, height adjustment assembly by a screw rod, foot and keeping a tight cap nut consisting of bottom three.

3 stainless steel pole.

3.1.3 Stainless steel ring funnel rack: Outside Ø110, Ø80 with inner wire, tail Ø8 stainless steel screws.

4 stainless steel funnel: mouth diameter 100mm, taper 60º, within the discharge port by 6mm.

5 stainless steel cylinder: about 200ml, the inner diameter of the inner high ratio of 1: 6, the base outer diameter of 70mm.

6, aluminum splice tray: external Ø80, inner Ø40, high 50, volume 100 ml.

7, aluminum governor filler: about 250 ml, outer Ø80 with wire.

8, the governor filler holder: external Ø110, Ø80 with inner wire, tail Ø8 stainless steel screws.

Instrument Accessories :

1, canopy-shaped gauge: bottom diameter Ø50, top diameter Ø15, within the specified height 10mm, outside the high 30.

2, pagoda-shaped gauge: bottom diameter Ø110, top diameter Ø20, regulation high 40mm.

3, frosted glass piece: 60 * 60mm.

4, dropping bottle: 60ml.

5, flat painting brush

6, stainless steel ruler

7 breadwinner wrenches and wrench

8, cotton

9 sample cup

Test object
Various metal powders: such as aluminum powder, zirconium powder, nickel powder, tungsten powder, tin powder, zinc powder, molybdenum powder, magnesium powder, copper powder and other precious metals, an alloy powder or metal oxide powder and the like.
Non-metallic powder: such as talc, kaolin, calcium carbonate, coal, phosphor, brucite, calcite, wollastonite, tourmaline, diamond, barite, fluorite, zeolite, boron carbide, clay, graphite, quartz, gypsum, bentonite, diatomaceous earth, zirconium silicate, alumina, mica, clay, titanium dioxide and the like.
Other powders: such as soil, dyes, pharmaceuticals, pesticides, abrasives, paints, food additives, catalysts, cement, sand and other rivers.