The bulk density of ordinary abrasive bulk density measuring device measuring instrument diamond powder bulk density meter natural bulk density

FT-103 bulk density tester

FT-103 bulk density tester It is based on national standards GB / T 16913.3-1997 provisions of design and production. The device is suitable for the determination of bulk density of dust.

FT-103 bulk density tester Please refer to the sample collection GB / T 16913.1-1997 dust Physics Experiment Part 1: Dust samples collected in the relevant regulations.

FT-103 bulk density tester Principle: Dust from the funnel mouth full of free fall at a certain height measuring cup; mass per unit volume of dust inside the cup measured bulk state, that dust bulk density.

FT-103 bulk density tester Structure: funnel (flow outlet diameter 12.7mm)

Funnel made of stainless steel, which funnel taper of 60 ° ± 0.5

FT-103A activated clay bulk density tester

GB 25571 Bulk density tester HGT2764 bulk density measuring device / industrial sodium peroxide bulk density measuring device

FT-103A activated clay bulk density measuring device Is based on national standards GB / T 25571-2010 national food safety standards, food additive provisions of activated clay design, production. The device is suitable for the determination of food additives, activated clay bulk density, while also meet HGT2764-2008 peroxide sodium carbonate industry industry standards for bulk density measuring device requirements.

FT-103A activated clay bulk density measuring device Principle: Dust from the funnel mouth full of free fall at a certain height measuring cup; quality measured within the measuring cup bulk state unit volume, namely bulk density.

FT-103A activated clay bulk density measuring device Structure: 2.1: funnel flow outlet diameter 30mm; funnel height: 135mm, funnel made of stainless steel, 2.2: cylinder diameter: 80mm, volume: 500ml

FT-106 ordinary abrasive bulk density tester (Original DMP-II)

FT-106 ordinary abrasive bulk density tester According to international standard ISO9136: 1989 (Determination of bulk density coarse grains) and industry standard JB / T7984.2-1999 (Ordinary coarse grit abrasive Determination of bulk density) of the relevant technical requirements of development and production of special detection equipment, while meeting the GB / T20316.1-2009 bulk density tester requirements; suitable for detecting manufacturing bonded abrasives and coated abrasives coarse particles ordinary abrasive bulk density, but also for the detection of other granular materials Bulk density Its detection methods and results and generic detection methods internationally with full versatility.
FT-106 ordinary abrasive bulk density tester The main technical parameters
2.1 Measurement error: ≤ ± 0.02g / cm3.
2.2 measuring cylinder volume: 200 ± 0.5cm3.
2.3 Dimensions: 230mm (length) * 250mm (width) * 425mm (H)

FT-106 ordinary abrasive bulk density tester

Note: Specific parameters, please keep in touch with us, as well as related products.

FT-106A powder bulk density tester It is based on the international standard ISO9136-2: (E) (abrasives - Determination of bulk density - Part II: Powder) 1999 related to the technical requirements of development and production of special detection equipment.

FT-106A powder bulk density tester Scope: suitable for detecting manufacturing bonded abrasives and coated abrasives with powder bulk density, but also for the detection of diamond powder and bulk density of other fine powdery material, its detection methods and results and generic detection methods internationally have. complete versatility.

FT-106A powder bulk density tester The main technical parameters: funnel under the port diameter: 28mm ; Cylinder volume: 200ml; Funnel spout height: 38mm ; Height of the drop measured powder: 140mm.

FT-106B superhard material bulk density tester Based on industry standards JB / T3584-1999 (( Superhard abrasive bulk density measurement method ) ) Develop

The company also produces sells the following related products :

FT-100 tap density tester; FT-101 Scott capacity meter Bulk Density Tester
FT-102 Hall flow meter / Bulk Density Tester - stainless steel; FL4-1 Hall flow meter / powder flowability tester - brass FT-103 bulk density tester; FT-103A activated clay bulk density determination equipment
FT-104 alumina bulk density tester; FT-104A alumina repose angle measurement
FT-104B repose angle measurement; FT-105 Apparent density analyzer
FT-105A active agents apparent density measuring device; FT-105B slurry was apparent density measuring device
FT-105C ASTM plastic apparent densitometer; FT-106 abrasive bulk density tester (Original DMP-II)
FT-106A powder bulk density tester; FT-106B superhard material bulk density tester
FZS4-4 tap density tester FT-102A vibration funnel bulk density tester

The bulk density of ordinary abrasive bulk density measuring device measuring instrument diamond powder bulk density meter natural bulk density

FT-103 bulk density tester

FT-103 bulk density tester It is based on national standards GB / T 16913.3-1997 provisions of design and production. The device is suitable for the determination of bulk density of dust.

FT-103 bulk density tester Please refer to the sample collection GB / T 16913.1-1997 dust Physics Experiment Part 1: Dust samples collected in the relevant regulations.

FT-103 bulk density tester Principle: Dust from the funnel mouth full of free fall at a certain height measuring cup; mass per unit volume of dust inside the cup measured bulk state, that dust bulk density.

FT-103 bulk density tester Structure: funnel (flow outlet diameter 12.7mm)

Funnel made of stainless steel, which funnel taper of 60 ° ± 0.5

FT-103A activated clay bulk density tester

GB 25571 Bulk density tester HGT2764 bulk density measuring device / industrial sodium peroxide bulk density measuring device

FT-103A activated clay bulk density measuring device Is based on national standards GB / T 25571-2010 national food safety standards, food additive provisions of activated clay design, production. The device is suitable for the determination of food additives, activated clay bulk density, while also meet HGT2764-2008 peroxide sodium carbonate industry industry standards for bulk density measuring device requirements.

FT-103A activated clay bulk density measuring device Principle: Dust from the funnel mouth full of free fall at a certain height measuring cup; quality measured within the measuring cup bulk state unit volume, namely bulk density.

FT-103A activated clay bulk density measuring device Structure: 2.1: funnel flow outlet diameter 30mm; funnel height: 135mm, funnel made of stainless steel, 2.2: cylinder diameter: 80mm, volume: 500ml

FT-106 ordinary abrasive bulk density tester (Original DMP-II)

FT-106 ordinary abrasive bulk density tester According to international standard ISO9136: 1989 (Determination of bulk density coarse grains) and industry standard JB / T7984.2-1999 (Ordinary coarse grit abrasive Determination of bulk density) of the relevant technical requirements of development and production of special detection equipment, while meeting the GB / T20316.1-2009 bulk density tester requirements; suitable for detecting manufacturing bonded abrasives and coated abrasives coarse particles ordinary abrasive bulk density, but also for the detection of other granular materials Bulk density Its detection methods and results and generic detection methods internationally with full versatility.
FT-106 ordinary abrasive bulk density tester The main technical parameters
2.1 Measurement error: ≤ ± 0.02g / cm3.
2.2 measuring cylinder volume: 200 ± 0.5cm3.
2.3 Dimensions: 230mm (length) * 250mm (width) * 425mm (H)

FT-106 ordinary abrasive bulk density tester

Note: Specific parameters, please keep in touch with us, as well as related products.

FT-106A powder bulk density tester It is based on the international standard ISO9136-2: (E) (abrasives - Determination of bulk density - Part II: Powder) 1999 related to the technical requirements of development and production of special detection equipment.

FT-106A powder bulk density tester Scope: suitable for detecting manufacturing bonded abrasives and coated abrasives with powder bulk density, but also for the detection of diamond powder and bulk density of other fine powdery material, its detection methods and results and generic detection methods internationally have. complete versatility.

FT-106A powder bulk density tester The main technical parameters: funnel under the port diameter: 28mm ; Cylinder volume: 200ml; Funnel spout height: 38mm ; Height of the drop measured powder: 140mm.

FT-106B superhard material bulk density tester Based on industry standards JB / T3584-1999 (( Superhard abrasive bulk density measurement method ) ) Develop

The company also produces sells the following related products :

FT-100 tap density tester; FT-101 Scott capacity meter Bulk Density Tester
FT-102 Hall flow meter / Bulk Density Tester - stainless steel; FL4-1 Hall flow meter / powder flowability tester - brass FT-103 bulk density tester; FT-103A activated clay bulk density determination equipment
FT-104 alumina bulk density tester; FT-104A alumina repose angle measurement
FT-104B repose angle measurement; FT-105 Apparent density analyzer
FT-105A active agents apparent density measuring device; FT-105B slurry was apparent density measuring device
FT-105C ASTM plastic apparent densitometer; FT-106 abrasive bulk density tester (Original DMP-II)
FT-106A powder bulk density tester; FT-106B superhard material bulk density tester
FZS4-4 tap density tester FT-102A vibration funnel bulk density tester

The bulk density of ordinary abrasive bulk density measuring device measuring instrument diamond powder bulk density meter natural bulk density